Jvc KD-APD89 User Manual download pdf (Page 193)

KD-G844

Installation/Connection Manual

0108DTSMDTJEIN

GET0523-002A

[UI]

Handles

Lock nut (M5)

Rubber

cushion

A / B

Hard case/Control

panel

Sleeve

Power cord

Battery

Remote controller

Heat sink

Mounting bolt (M4 × 5 mm;

M5 × 12.5 mm)

Washer (ø5)

Trim plate

Insert the two handles, then pull them as illustrated

so that the unit can be removed.

When installing the unit

without using the sleeve

In a Toyota car for example, first remove the

car radio and install the unit in its place.

When using the optional stay

Note :

When installing the unit on the mounting

bracket, make sure to use the 8 mm-long

screws. If longer screws are used, they could

damage the unit.

Install the unit at an angle

of less than 30˚.

Bracket*

Flat head screws (M5 × 8 mm)*

Bracket*

Do the required electrical connections.

Bend the appropriate tabs to

hold the sleeve firmly in place.

Fire wall

Dashboard

Screw (option)

Stay (option)

Pocket

This unit is designed to operate on 12 V DC, NEGATIVE ground electrical systems. If your vehicle does

not have this system, a voltage inverter is required, which can be purchased at JVC car audio dealers.

WARNINGS

To prevent short circuits, we recommend that you disconnect the battery’s negative terminal and make all

electrical connections before installing the unit.

• Be sure to ground this unit to the car’s chassis again after installation.

Notes:

• Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC car audio

dealer.

• It is recommended to connect speakers with a maximum power of more than 50 W (both at the rear

and at the front, with an impedance of 4 Ω to 8 Ω). If the maximum power is less than 50 W, change

“Amp Gain” setting to prevent the speakers from being damaged (see page 25 of the INSTRUCTIONS).

• To prevent short circuits, cover the terminals of the UNUSED leads with insulating tape.

• The heat sink becomes very hot after use. Be careful not to touch it when removing this unit.

PRECAUTIONS on power supply and speaker connections:

• DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the unit

will be seriously damaged.

• BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker wiring in

your car.

Parts list for installation and connection

The following parts are provided for this unit. If any item is missing, consult your JVC car audio

dealer immediately.

TROUBLESHOOTING

• The fuse blows.

* Are the red and black leads connected correctly?

• Power cannot be turned on.

* Is the yellow lead connected?

• No sound from the speakers.

* Is the speaker output lead short-circuited?

• Sound is distorted.

* Is the speaker output lead grounded?

* Are the “–” terminals of L and R speakers grounded in common?

• Noise interfere with sounds.

* Is the rear ground terminal connected to the car’s chassis using shorter and thicker cords?

• This unit becomes hot.

* Is the speaker output lead grounded?

* Are the “–” terminals of L and R speakers grounded in common?

• This unit does not work at all.

* Have you reset your unit?

INSTALLATION (IN-DASH MOUNTING)

The following illustration shows a typical installation. If you have any questions or require information

regarding installation kits, consult your JVC car audio dealer or a company supplying kits.

• If you are not sure how to install this unit correctly, have it installed by a qualified technician.

Removing the unit

Before removing the unit, release the rear section.

Flat head screws

(M5 × 8 mm)*

When you stand the unit, be careful not to damage the fuse on the rear.

Avoid touching the connectors.

Not supplied for this unit.

Install_KD-G844[UI]f.indd 1Install_KD-G844[UI]f.indd 1 12/14/07 12:49:51 PM12/14/07 12:49:51 PM

1 ... 192 193 194 ... 472

Comments to this Manuals

No comments

Jvc KD-APD89 User Manual Page 193

Comments to this Manuals

Related products and manuals for Car speakers Jvc KD-APD89