Jvc RX-8040B User Manual download pdf (Page 66)

English

SOLUTION

Deactivate the Zone 2 front speakers.

Activate all connected speakers correctly.

(See “Setting the speakers” on page 34.)

Turn off Analog Direct. (See page 23.)

Select the source other than DVD MULTI.

(See page 20.)

Play back software bearing the mark Dolby

Digital EX or DTS-ES and set

“EX/ES/PLIIx” setting to “AUTO” or “ON.”

(See page 45.)

Plug the power cord into an AC outlet.

Connect it to the screw marked (H).

Move speakers away from the turntable.

If subwoofer is connected, set “SUB

WOOFER” to “YES” so that SUBWOOFER

OUT ON/OFF works.

1. Press

STANDBY/ON on the front

panel to turn off the receiver.

2. Stop the playback source.

3. Turn on the receiver again, and adjust the

volume.

Press

STANDBY/ON on the front panel

to turn off the receiver, then check the

speaker wiring.

If “OVERLOAD” does not disappear,

unplug the AC power cord, then plug it back

again.

If speaker wiring is not short-circuited,

contact your dealer.

Set the component video input setting

(“VIDEO IN DBS” and “VIDEO IN VCR1”)

correctly. (See page 38.)

Deactivate the Zone 2 front speakers.

Press

STANDBY/ON on the front panel

to turn off the receiver. After unplugging the

AC power cord, contact your dealer.

Press

STANDBY/ON on the front panel

to turn off the receiver. After unplugging the

AC power cord, consult your dealer.

Set the selector correctly either to “ZONE 1”

or to “ZONE 2.”

Set the selector correctly either to “TV” or to

“CATV/DBS.”

Consult your dealer.

Replace batteries. (See page 15.)

Select the correct remote control operation

mode. (See pages 56 to 61.)

PROBLEM

Multi-channel reproduction mode

cannot be used for Zone 1 sources.

Expected surround effect cannot be

obtained.

No sound effect such as the Surround

mode, DSP mode and equalization

pattern.

“DOLBY D EX,” “ES DSCRT,” or

“ES MATRIX” cannot be select as the

Surround mode.

The display does not light up.

Noise is heard during record playing.

Howling during record playing.

“NO SUBWFR” appears on the

display.

“OVERLOAD” starts flashing on the

display.

No playback picture of the VCR 1 or

DBS tuner can be viewed.

DVD MULTI is cannot be select as the

source.

“DSP NG” starts flashing on the

display.

The STANDBY lamp goes off after

turning on the power, but soon the

receiver turns off again (into standby

mode).

Remote control does not work.

Remote control does not work

properly.

POSSIBLE CAUSE

ZONE 2 SPEAKERS are activated.

Speakers are deactivated on the Quick

Speaker Setup or the Basic Setting.

Analog Direct is turned on.

DVD MULTI is selected as the source

(equalization pattern is effective).

Software itself is not Dolby Digital EX or

DTS-ES software, or “EX/ES/PLIIx” setting

is not correct.

The power cord is not plugged in.

A ground cable of the turntable is not

connected to the screw marked (H).

Your turntable is too close to speakers.

SUBWOOFER OUT ON/OFF is pressed

while “SUB WOOFER” is set to “NO.”

Speakers are overloaded because of high

volume either in Zone 1 or in Zone 2.

Speakers are overloaded because of a short

circuit of the speaker terminals.

Setting of the component video input are not

done for correctly.

ZONE 2 SPEAKERS are activated.

The built-in microcomputer is not

functioning correctly.

Very high voltage or very low voltage is

applied to the unit, or built-in power

amplifier becomes out of order.

The ZONE 1/ZONE 2 selector is not set

correctly.

The TV operation mode selector is not set

correctly.

RF communication between the receiver and

the remote control is interrupted from

outside.

Batteries are weak.

Incorrect remote control operation mode is

selected.

General

Surround and DSP modes

53-65_8040[C].p65 04.5.14, 11:3064

1 2 ... 61 62 63 64 65 66 67 68 69 70 71 ... 133 134

Comments to this Manuals

No comments

Jvc RX-8040B User Manual Page 66

Comments to this Manuals

Related products and manuals for Receivers and Amplifiers Jvc RX-8040B