Jvc RX-8040B User Manual Page 26
- Page / 134
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
24
English
The following basic operations are possible only using the
remote control.
Reinforcing the Bass
You can boost the bass level.
• Once you have made an adjustment, it is memorized for each
source.
Press BASS BOOST to boost the bass level.
The B. BOOST indicator lights up on the unit’s display.
• Each time you press the button, Bass Boost turns on (“BOOST
ON”) and off (“BOOST OFF”) alternately.
Notes:
• This function affects only the sounds from the front speakers,
center speaker, and subwoofer.
• When Analog Direct is in use (see page 23), the Bass Boost is
canceled temporarily.
Muting the Zone 1 Sound
Press MUTING to mute the sound through all speakers in
Zone 1 and headphones connected.
“MUTING” appears on the unit’s display and the volume turns off
(the VOLUME level indicator goes off).
To restore the sound, press MUTING again so that the VOLUME
level indicator and “MUTING OFF” appear on the unit’s display.
• Turning MASTER VOLUME on the unit or pressing
VOLUME +/– on the remote control also restores the sound.
Changing the Display Brightness
You can dim the unit’s display.
Press DIMMER.
• Each time you press the button, the brightness level of the unit’s
display changes as follows:
Changing the Source Name
When you have connected an MD recorder to the TAPE/MD IN
jacks or a DBS tuner to the TV SOUND/DBS IN jacks on the rear
panel, change the source name which will appear on the display.
When changing the source name from “TV” to “DBS”:
1. Press TV SOUND/DBS.
• Make sure “TV” appears on the display.
2. Press and hold TV SOUND/DBS until “ASSGN DBS”
appears on the display.
Note:
When connecting a DBS tuner to the TV SOUND/DBS IN jacks,
change the source name to “DBS,” which will appear on the display
when selected as the source. Otherwise you cannot view any picture
from DBS tuner.
When changing the source name from “TAPE” to “MD”:
1. Press TAPE/MD.
• Make sure “TAPE” appears on the display.
2. Press and hold TAPE/MD until “ASSGN MD” appears on
the display.
To change the source name to “TV” and “TAPE,” repeat the
same procedure above.
• While selecting “DBS” as the Zone 2 source, you cannot change
the source name to “TV.”
Notes:
• Once you change the source name, it is applied both for the Zone 1
and Zone 2 sources.
• Without changing the source name, you can still use the connected
components. However, there may be some inconvenience.
–“TAPE” or “TV” will appear on the display when you select the MD
recorder or DBS tuner.
– You cannot use the digital input (see page 22) for the MD
recorder.
– You cannot use the COMPU LINK remote control system (see
page 51) to operate the MD recorder.
Remote
NOT
LINEAR PCM
L
R
ANALOG
VOLUME
SPEAKERS 1
ZONE 1
Reinforcing the
Bass
Using the Sleep
Timer
Muting the Sound
Changing
the Display
Brightness
MUTING
BASS BOOST
SLEEP DIMMER
Dimmer Much dimmer
Canceled
(Normal display)
16-29_8040[C].p65 04.5.14, 11:2924
- RX-8040B 1
- For Canada/pour Le Canada 2
- Introduction 3
- Table of Contents 4
- Parts Identification 5
- Front Panel 6
- How to open the front door 6
- CAUTION : SPEAKER IMPEDANCE 8
- Getting Started 9
- Speaker connections 10
- Connecting the subwoofer 10
- SURR BACK 11
- Analog connections 12
- Video component connections 13
- RIGHT LEFT 15
- Digital connections 16
- Setting up the RF rod antenna 16
- At an angle of 17
- Multi-room Operations 18
- On the front panel: 19
- On the remote control: 19
- Zone 1 (Main Room) Operations 21
- SPEAKERS 1 22
- LINEAR PCM 23
- DGTL AUTO DGTL D.D 24
- DGTL DTS 24
- Setting the Dynamic Range 25
- Attenuating the Input Signal 25
- Making Sounds Natural 25
- Dimmer Much dimmer 26
- Canceled 26
- Using the Sleep Timer 27
- Zone 2 (Sub-room) Operations 28
- Adjusting the Zone 2 Volume 30
- Activating the Zone 2 Front 31
- Speakers 31
- Muting the Zone 2 Sound 31
- 1 ZONE 2 31
- Receiving Radio Broadcasts 32
- To store the preset stations 33
- Basic Settings 34
- Basic Setting Items 35
- Setting the speakers 36
- Setting the speaker distance 37
- Setting the bass sounds 37
- Center speaker setting 38
- SMALL/LARGE NONE 38
- “DBS” appears (see page 24) 39
- Setting the Zone 2/Speakers 2 40
- Adjusting Sound 41
- EQ 1kHz, EQ 4kHz, EQ16kHz 42
- Adjustable speakers 42
- Surround and DSP modes 43
- Using the Surround Modes 44
- Digital Theater Systems, Inc 45
- PRO LOGIC 46
- SPEAKERS 1 46
- EX/ES/PLIIx 47
- Virtual 6.1-channel surround 49
- 3D Headphone mode—3D H PHONE 49
- Using the DSP Modes 50
- To cancel the DSP modes 51
- AUDIO POWER 52
- One-Touch Video Play 56
- DVD player 60
- STOP PAUSE 62
- * Initial setting 64
- Troubleshooting 65
- SOLUTION 66
- POSSIBLE CAUSE 66
- Specifications 67
- Table des matières 69
- Identification des parties 70
- Panneau avant 71
- Affichage 71
- Comment ouvrir la porte avant 71
- Pour commencer 74
- Connexions analogiques 77
- Connexion des appareils vidéo 78
- Remarque: 78
- Remarques: 79
- Fonctionnement multi-pièces 83
- Réglages de base 99
- Français 100
- OPTICAL signifie VCR1 104
- Ajustment du son 106
- Laboratories 110
- Utilisation des modes DSP 115
- Guide de dépannage 130
- Spécifications 132
- AUDIO/VIDEO CONTROL RECEIVER 133
Related products and manuals for Receivers and Amplifiers Jvc RX-8040B
(36 pages)
(126 pages)
© 2020, manymanuals.com. All rights reserved. | 0.227 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals