Jvc RX-8040B User Manual download pdf (Page 43)

English

You can also use the remote control for adjusting the speaker

output level and DSP (DAP modes and Mono Film) effect levels

(“EFFECT” and “LIVENESS”).

To adjust the speaker output level:

1. Press SOUND.

The 10 keys are activated for sound adjustments.

2. Press TEST to check if you can hear the sounds through

all the speakers at equal level.

Test tone comes out of the speakers in the following order.

• No test tone comes out of the speakers for which the

speaker setting is set to “NONE” (or “NO” for the

subwoofer).

• While Zone 2 speakers are activated, no test tone comes out

from center, surround, and surround back speakers.

FRNT L (Left front speaker)

CENTER (Center speaker)

FRNT R (Right front speaker)

SURR R (Right surround speaker)

SBACK (Surround back speaker)

SURR L (Left surround speaker)

SUBWFR (Subwoofer)

(Back to the beginning)

3. Select the speaker you want to adjust.

• To select the left front speaker, press FRONT•L.

• To select the center speaker, press CENTER.

• To select the right front speaker, press FRONT•R.

• To select the right surround speaker, press SURR•R.

• To select the surround back speaker, press SURR BK.

• To select the left surround speaker, press SURR•L.

• To select the subwoofer, press SUBWFR.

The selected speaker name appears on the remote’s display for

a while.

4. Press LEVEL +/– to adjust the speaker output levels.

Notes:

• When you press each button once, the current level for the

selected speaker appears on the unit’s display, and the test

tone comes out of the selected speaker.

• If no adjustment is done for about 4 seconds, the adjustment

mode for the selected speaker is canceled.

5. Repeat steps 3 and 4 to adjust the other speaker output

levels.

6. Press TEST again to stop the test tone.

To adjust the DSP effect levels:

1. Press SOUND.

The 10 keys are activated for sound adjustments.

2. Press EFFECT repeatedly to adjust the effect level.

3. Press LIVENESS repeatedly to adjust the liveness effect.

Adjusting the sound parameters for the

Surround and DSP modes

You can adjust the Surround and DSP sound parameters to your

preference. (For Surround and DSP modes, see pages 42 to 49.)

Adjustable parameters

You can adjust the following parameters:

For Surround and DSP modes (when the center speaker is

connected)

• This setting is common to all Surround modes, and is

memorized separately for DSP modes.

CTR TONE Adjust the center tone. As the number

increases, the dialogue becomes clearer so

that the human voices change from soft to

sharp.

(Adjustable range: 1 to 5. “3” is the initial

setting, and normally select this.)

For DAP modes and Mono Film

• Once you have made an adjustment, it is memorized for each

mode.

EFFECT Adjust the effect level. As the number

increases, the effect becomes stronger.

(Adjustable range: 1 to 5. “3” is the initial

setting, and normally select this.)

ROOMSIZE Adjust the virtual room size. As the number

increases, the interval between reflections

increases so that you will feel as if you were

in a larger room.

(Adjustable range: 1 to 5. “3” is the initial

setting, and normally select this.)

LIVENESS Adjust the liveness effect. As the number

increases, the attenuation level of reflections

over time decreases so that acoustics change

from “Dead” to “Live.”

(Adjustable range: 1 to 5. “3” is the initial

setting, and normally select this.)

For Pro Logic IIx Music and Pro Logic II Music

PNRM CNTRL Select “ON” to add “wraparound” sound

effect with side-wall image. (Initial setting:

“OFF.”)

CNTR WIDTH Adjust the center channel localization

between the center speaker and the left/right

front speakers. As the number increases, the

center channel sound moves toward the left

and right speakers. (Adjustable range: OFF

and 1 to 7. “3” is the initial setting, and

normally select this.)

DIMENSION Adjust the sound localization position. As the

number increases, the sound localization

moves towards forward from backward.

(Adjustable range: 1 to 7. “4” is the initial

setting, and normally select this.)

For Neo:6 Music only

CNTR GAIN Adjust the sound localization of the center

channel. As the number increases, center

channel will be localized clearly.

(Adjustable range: 0 to 1.0. “0.3” is the initial

setting, and normally select this.)

EFFECT

LIVENESS

SOUND

123

456

100

TEST

39-41_8040[C].p65 04.5.14, 11:2941

1 2 ... 38 39 40 41 42 43 44 45 46 47 48 ... 133 134

Comments to this Manuals

No comments

Jvc RX-8040B User Manual Page 43

Comments to this Manuals

Related products and manuals for Receivers and Amplifiers Jvc RX-8040B