Jvc RX-8040B User Manual Page 65
- Page / 134
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
63
English
PROBLEM
The buttons and controls on the front
panel do not work.
No sound from the speakers in Zone 1.
No sound from the front speakers in
Zone 2.
The SPEAKERS ON/OFF 2/ZONE 2
button does not work.
CD tracks are skipped, tape is rewound,
or radio station is changed
unintentionally.
The receiver does not work correctly as
you operate it.
“TURN ON ZONE1 OR ZONE2”
appears on the display.
Continuous hissing or buzzing during
FM reception.
Occasional cracking noise during FM
reception.
Troubleshooting
Use this chart to help you solve daily operational problems. If there is any problem you cannot solve, contact your JVC‘s
service center.
POSSIBLE CAUSE
The multi-room function is not set
correctly.
Speaker signal cables are not connected
properly.
The SPEAKERS ON/OFF 1 and
SPEAKERS ON/OFF 2/ZONE 2 buttons
are not set correctly.
Incorrect source is selected for Zone 1.
Muting is activated for the Zone 1 source.
Incorrect input mode (analog or digital) is
selected.
Connections are incorrect.
Speaker signal cables are not connected
properly.
Zone 1/2 setting for the speakers connected
to the FRONT2/ZONE2 SPEAKERS
terminals are not set correctly.
Amplifier connected to the ZONE 2
PREOUT is not turned on.
Incorrect source is selected for Zone 2.
Muting is activated for the Zone 2 source.
Connections are incorrect.
The speakers connected to the FRONT2/
ZONE2 SPEAKERS terminals are preset
for Zone 1 usage.
When the same source is selected both for
Zone 1 and Zone 2, the source in one zone
affects the source in the other zone.
Zone 1 and Zone 2 operations are done at
the same time.
The receiver is turned on with the Zone 1
and Zone 2 sounds deactivated.
Incoming signal is too weak.
The station is too far away.
An incorrect antenna is used.
Antennas are not connected properly.
Ignition noise from automobiles.
SOLUTION
• Press ZONE 1 ON/OFF for Zone 1
operations.
• Press ZONE 2 ON/OFF and ZONE 2
CONTROL for Zone 2 operations.
Check speaker wiring and reconnect if
necessary. (See page 8.)
Press SPEAKERS ON/OFF 1 and
SPEAKERS ON/OFF 2/ZONE 2 correctly.
(See page 21.)
Select the correct source for Zone 1.
Press MUTING to cancel the mute.
(See page 24.)
Select the correct input mode (analog or
digital). (See page 22.)
Check connections.
For analog connections, see pages 10 to 13.
For digital connections, see page 14.
Check speaker connection and reconnect if
necessary. (See page 16.)
Set the Zone 1/2 setting for the speakers
correctly to use them as the Zone 2 front
speakers. (See page 38.)
Turn on the amplifier.
Select the correct source for Zone 2.
Press MUTING to cancel the mute.
(See page 29.)
Make analog connections for Zone 2.
For analog connections, see pages 10 to 13.
Set them for Zone 2 usage. (See page 38.)
This is normal, not a malfunction of the unit.
Selecting different sources for Zone 1 and
Zone 2 will avoid these troubles.
If this happens, perform the same operation
again.
• Press ZONE 1 ON/OFF for Zone 1
operations.
• Press ZONE 2 ON/OFF for Zone 2
operations.
Connect an outdoor FM antenna or contact
your dealer. (See page 7.)
Select a new station.
Check with your dealer to be sure you have
the correct antenna.
Check connections. (See page 7.)
Move the antenna farther from automobile
traffic.
Multi-room operations (Zone 1/Zone 2)
FM/AM
53-65_8040[C].p65 04.5.14, 11:3063
- RX-8040B 1
- For Canada/pour Le Canada 2
- Introduction 3
- Table of Contents 4
- Parts Identification 5
- Front Panel 6
- How to open the front door 6
- CAUTION : SPEAKER IMPEDANCE 8
- Getting Started 9
- Speaker connections 10
- Connecting the subwoofer 10
- SURR BACK 11
- Analog connections 12
- Video component connections 13
- RIGHT LEFT 15
- Digital connections 16
- Setting up the RF rod antenna 16
- At an angle of 17
- Multi-room Operations 18
- On the front panel: 19
- On the remote control: 19
- Zone 1 (Main Room) Operations 21
- SPEAKERS 1 22
- LINEAR PCM 23
- DGTL AUTO DGTL D.D 24
- DGTL DTS 24
- Setting the Dynamic Range 25
- Attenuating the Input Signal 25
- Making Sounds Natural 25
- Dimmer Much dimmer 26
- Canceled 26
- Using the Sleep Timer 27
- Zone 2 (Sub-room) Operations 28
- Adjusting the Zone 2 Volume 30
- Activating the Zone 2 Front 31
- Speakers 31
- Muting the Zone 2 Sound 31
- 1 ZONE 2 31
- Receiving Radio Broadcasts 32
- To store the preset stations 33
- Basic Settings 34
- Basic Setting Items 35
- Setting the speakers 36
- Setting the speaker distance 37
- Setting the bass sounds 37
- Center speaker setting 38
- SMALL/LARGE NONE 38
- “DBS” appears (see page 24) 39
- Setting the Zone 2/Speakers 2 40
- Adjusting Sound 41
- EQ 1kHz, EQ 4kHz, EQ16kHz 42
- Adjustable speakers 42
- Surround and DSP modes 43
- Using the Surround Modes 44
- Digital Theater Systems, Inc 45
- PRO LOGIC 46
- SPEAKERS 1 46
- EX/ES/PLIIx 47
- Virtual 6.1-channel surround 49
- 3D Headphone mode—3D H PHONE 49
- Using the DSP Modes 50
- To cancel the DSP modes 51
- AUDIO POWER 52
- One-Touch Video Play 56
- DVD player 60
- STOP PAUSE 62
- * Initial setting 64
- Troubleshooting 65
- SOLUTION 66
- POSSIBLE CAUSE 66
- Specifications 67
- Table des matières 69
- Identification des parties 70
- Panneau avant 71
- Affichage 71
- Comment ouvrir la porte avant 71
- Pour commencer 74
- Connexions analogiques 77
- Connexion des appareils vidéo 78
- Remarque: 78
- Remarques: 79
- Fonctionnement multi-pièces 83
- Réglages de base 99
- Français 100
- OPTICAL signifie VCR1 104
- Ajustment du son 106
- Laboratories 110
- Utilisation des modes DSP 115
- Guide de dépannage 130
- Spécifications 132
- AUDIO/VIDEO CONTROL RECEIVER 133
Related products and manuals for Receivers and Amplifiers Jvc RX-8040B
(36 pages)
(126 pages)
© 2020, manymanuals.com. All rights reserved. | 0.481 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals