JVC RX-7520VBK User Manual download pdf (Page 34)

English

COMPU LINK Remote Control System

Automatic Power On/Off (Standby): only possible with the

COMPU LINK-3 and COMPU LINK-4

Both the CD player and cassette deck (or CD recorder) turn on and

off (standby) along with the receiver.

When you turn on the receiver, the CD player or cassette deck (or

CD recorder) will turn on automatically, depending on which

component has been previously selected.

When you turn off the receiver, both the CD player and cassette

deck (or CD recorder) will turn off (standby).

Synchronized Recording

Synchronized recording means the cassette deck starts recording as

soon as a CD begins playing.

To use synchronized recording, follow these steps:

Put a tape in the cassette deck and a disc in the

CD player.

Press the record (¶) button and the pause (8)

button on the cassette deck at the same time.

This puts the cassette deck into recording pause.

If you do not press the record (¶) button and pause (8) button at

the same time, the synchronized recording feature will not

operate.

Press the play (3) button on the CD player.

The source changes on the receiver, and as soon as play starts,

the cassette deck starts recording. When the play ends, the

cassette deck enters recording pause, and stops about 4 seconds

later.

Notes:

• During synchronized recording, the selected source cannot be

changed.

• If the power of any component is shut off during synchronized

recording, the COMPU LINK remote control system may not

operate properly. In this case, you must start again from the

beginning.

The COMPU LINK remote control system allows you to operate

JVC’s audio components through the remote sensor on the receiver.

To use this remote control system, you need to connect JVC’s audio

components through the COMPU LINK-4 (SYNCHRO) jacks (see

below) in addition to the connections using cables with RCA pin

plugs (see pages 6 and 7).

• Make sure that the AC power cords of these components are

unplugged before connection. Plug the AC power cords only after

all connections are completed.

Notes:

• There are four versions of COMPU LINK remote control system.

This receiver is equipped with the fourth version—COMPU LINK-4.

This version is added systematic operations with the CD recorder to

the previous version—COMPU LINK-3.

• If your audio component has two COMPU LINK jacks, you can use

either one. If it has only one COMPU LINK jack, connect it so that it

is the last item in the series of components.

• To operate the cassette deck or CD recorder using the COMPU

LINK remote control system, set the source name correctly.

(See page 11.)

• Refer also to the manuals supplied with your audio components.

This remote control system allows you to use four functions listed

below.

Remote Control through the Remote Sensor on the Receiver

You can control the connected audio components through the remote

sensor on the receiver using this remote control. Aim the remote

control directly at the remote sensor on the receiver. For details, see

pages 34 and 35.

Automatic Source Selection

When you press the play (

3) button on a connected component or

on its own remote control, the receiver automatically turns on and

changes the source to the component. On the other hand, if you

select a new source on the receiver or on the remote control, the

selected component begins playing immediately.

In both cases, the previously selected source continues playing

without sound for a few seconds.

COMPU LINK-4

(SYNCHRO)

Cassette deck

CD recorder

CD player

EN30-42.RX-7520V[C]f.pm5 02.2.14, 4:33 PM31

1 2 ... 29 30 31 32 33 34 35 36 37 38 39 ... 45 46

Comments to this Manuals

No comments

JVC RX-7520VBK User Manual Page 34

Comments to this Manuals

Related products and manuals for AV receivers JVC RX-7520VBK