JVC RX-7520VBK User Manual download pdf (Page 14)

English

Adjusting the Volume

On the front panel:

To increase the volume,

turn MASTER VOLUME clockwise.

To decrease the volume,

turn it counterclockwise.

From the remote control:

To increase the volume, press VOLUME +.

To decrease the volume, press VOLUME –.

CAUTION:

Always set the volume to the minimum before starting any source. If

the volume is set at its high level, the sudden blast of sound energy

can permanently damage your hearing and/or ruin your speakers.

Note:

The volume level can be adjusted within the range of “0” (minimum) to

“50” (maximum).

Selecting the Front Speakers

When you have connected two pairs of the front speakers, you can

select which to use.

To use the speakers connected to the FRONT SPEAKERS 1

terminals, press SPEAKERS ON/OFF 1 so that the SPK 1 indicator

lights up on the display. (Make sure that the SPK 2 is not lit on the

display.)

To use the speakers connected to the FRONT SPEAKERS 2

terminals, press SPEAKERS ON/OFF 2 so that the SPK 2 indicator

lights up on the display. (Make sure that the SPK 1 is not lit on the

display.)

To use both set of the speakers, press SPEAKERS ON/OFF 1 and

2 so that the SPK 1 and SPK 2 indicators light up on the display.

To use neither set of the speakers, press SPEAKERS ON/OFF

1 and 2 so that the SPK 1 and SPK 2 indicators disappear from the

display.

Notes:

• If you select any of the Surround modes while using both the speakers

connected to the FRONT SPEAKERS

and

terminals, the

speakers connected to the FRONT SPEAKERS

terminals are

deactivated.

• While the Surround mode is in use, you can only select either the

speakers connected to the FRONT SPEAKERS

terminals.

• If you select DVD MULTI as the source while using both the speakers

connected to the FRONT SPEAKERS

and

terminals, the

speakers connected to the FRONT SPEAKERS

terminals are

deactivated.

• When selecting “DVD MULTI” as the source, you can only select

either the speakers connected to the FRONT SPEAKERS

terminals.

Remote

NOT

MASTER VOLUME

VOLUME

TAPE/CDR

SOURCE NAME

TAPE/CDR

SOURCE NAME

From the remote control

On the front panel

DVD VCR

TV SOUND

CD TAPE/CDR

SOURCE NAME

DVD MULTI

TAPE/CDR CD DVD DVD MULTI

FM/AM TV SOUND VCR

Changing the source name

When you connect a CD recorder to the

TAPE/CDR jacks on the rear panel, change the

source name shown on the display.

Press TAPE/CDR (SOURCE NAME).

• Make sure “TAPE” appears on the display.

Press and hold SOURCE NAME (TAPE/CDR)

until “ASSIGN CDR” appears on the display.

To change the source name from “CDR” to “TAPE,” repeat the

same procedure above (in step

, make sure “CDR” appears on the

display).

Note:

Without changing the source name, you can still use the connected

component. However, there may be some inconvenience:

–“TAPE” will appear on the display when you select the CD

recorder.

– You cannot use the digital input (see page 14) for the CD recorder.

– You cannot use the COMPU LINK remote control system (see page

31) to operate the CD recorder.

Selecting different sources for picture and sound

You can watch picture from a video component while listening to

sound from another component.

Press one of the audio source selecting buttons—

CD, TAPE/CDR, FM, AM (or FM/AM on the remote control),

while watching the picture from a video component such as the

VCR, or DVD player, etc.

Notes:

• Once you have selected a video source, pictures of the selected

source are sent to the TV until you select another video source.

• This function can use only when selecting the S-video or composite

video input terminal.

SPEAKERS ON/OFF

Remote

NOT

EN10-22.RX-7520V[C]f.pm5 02.2.14, 4:31 PM11

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 45 46

Comments to this Manuals

No comments

JVC RX-7520VBK User Manual Page 14

Comments to this Manuals

Related products and manuals for AV receivers JVC RX-7520VBK