JVC UX-T550 User Manual download pdf (Page 14)

Operate in the order shown

RADIO RECEPTION

~ Press the TUNER/BAND button.

● The power is switched on and a band and radio frequency will be

shown in the display.

Ÿ Select the band.

! Tune to the required station.

⁄ Adjust.

STEREO AUTO/MONO button (using the remote control unit)

Notes:

● When seek tuning to the required station is not possible because the

broadcast signal is too weak, press the 4 or ¢ button momentar-

ily to perform manual tuning.

● When the power is set to STANDBY, or another mode (TAPE, CD or

AUX) is selected, the last tuned frequency is stored in memory. When

the power is switched on again and TUNER/BAND button is pressed,

the same station will be tuned to.

Auto preset tuning (using the remote control unit)

This function scans the current band, detecting frequencies used to

broadcast signals, and stores the first 30 FM frequencies and 15 AM

(MW/LW) frequencies in memory automatically.

● Press the AUTO PRESET button for more than 2 seconds. The fre-

quencies of stations broadcasting signals can be stored in memory

automatically in the order of increasing frequency. (30 stations in FM

band and 15 stations in AM (MW/LW) band.)

Presetting stations (using the remote control unit)

30 stations in FM band and 15 stations in AM (MW/LW) band can be

preset as follows:

● Example: (Presetting an FM station broadcasting on 103.5 MHz to

preset button “15”)

Auto mode:

Set to this position when listening to or recording an FM stereo broad-

cast. The STEREO indicator lights when the FM stereo broadcast is

received.

MONO:

Set to this position when FM stereo reception is noisy.

When another station is tuned to in the MONO mode, the unit automati-

cally enters Auto mode.

Seek tuning

Press the 4 or ¢ button for one second or more. The unit enters

the seek tuning mode to tune in the nearest station automatically, so

the broadcast can be heard. In AM operation, the frequency moves

continuously from the MW to the LW band and vice versa.

Manual tuning

Each time the 4 or ¢ button is pressed, the unit steps through the

current frequency band. Tuning is done in steps of 50 kHz for FM and 9

kHz for AM (MW/LW).

In AM operation, the tuned frequency moves continuously from the MW

(522–1,629 kHz) to the LW (144–288 kHz) band and vice versa.

Press to move to higher frequency.

Press to move to lower frequencies.

AUTO

PRESET

Press for more than 2 seconds.

~ Press the TUNER/BAND button.

Ÿ Select the FM band using the TUNER/BAND button.

! Tune to the required station.

⁄ Press preset button “+10”, then “5” for more than 2 sec.

(When “15” blinks in the preset station display, the station has been

stored.)

● Repeat the above procedure for each of the other stations, using a

different preset button each time.

● Repeat the above procedure for the other band.

● To change preset stations

Perform step ⁄ above after tuning to the required station.

Notes:

● The previous stored station is erased when a new station is stored,

because the new station’s frequency replaces the previous frequency

in memory.

● When listening to an AM (MW/LW) broadcast, noise may be heard if

the remote control unit is used.

● All preset stations will be erased when the power cord is discon-

nected or a power failure occurs for more than 24 hours. In such

cases, store the stations again.

Using the antennas (see page 2)

FM: Connect the provided FM wire antenna.

AM (MW/LW): Adjust the position of AM (MW/LW) loop antenna.

Preset tuning

● The stations must be preset before this operation can be performed.

(Using the main unit)

1 Press the TUNER/BAND button.

2 Select the band using the TUNER/BAND button.

3 To select the requied preset station, turn the MULTI JOG dial.

(Using the remote control unit)

1 Press the TUNER/BAND button.

2 Select the band using the TUNER/BAND button.

3 Press the required preset station buttons (No. 1 – No. 10 and +10).

● The preset station number and frequency corresponding to the but-

ton pressed are shown.

Down

STEREO AUTO/MONO button

BAND

ONE TOUCH

REC

TAPE

OPEN

TUNER

TIMER/SNOOZE

STANDBY

AUX

MICRO COMPONENT SYSTEM UX-T550

VOLUME

ACTIVE HYPER

BASS PRO

SLEEP

+10

AUX

AUTO

PRESET

DISPLAY

PROGRAM RANDOM

REPEATBEAT CUT

REVERSE

MODE

STEREO

AUTO/MONO

MULTI CONTROLREW

TAPE TUNER

BAND

C D

CLOCK

AUTO TAPE SELECTOR

⁄

SLEEP

+10

AUX

AUTO

PRESET

DISPLAY

REVERSE

MODE

STEREO

AUTO/MONO

MULTI CONTROLREW

TAPE TUNER

BAND

C D

⁄

UX-T550(B)_body.pm6 12/12/00, 3:11 PM11

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 20

Comments to this Manuals

No comments

JVC UX-T550 User Manual Page 14

Comments to this Manuals

Related products and manuals for CD players JVC UX-T550