JVC SR-V10E User Manual download pdf (Page 60)

Masterpage:Left-FullCol

Filename [SR-V10E4-EN.fm]

Page 60 August 8, 2002 5:41 pm

TROUBLESHOOTING (cont.)

RECORDING

TIMER RECORDING

SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION

1. Recording cannot be started. ● There is no cassette loaded. Load a cassette with the record safety tab

intact. If the tab has been removed, set

“REC SAFETY” to “OFF” (

墌

pg. 48).

● The loaded cassette has had its record

safety tab removed and “REC SAFETY”

is set to “ON”.

Set “REC SAFETY” to “OFF” (

墌

pg. 48),

or using adhesive tape, cover the hole

where the tab was removed.

2. TV broadcasts cannot be recorded. ● “L-1”, “F-1”, “S-1” or “S-2” has been

selected as the input mode.

Set to the desired channel.

3. Tape-to-tape editing is not possible. ● The source (another video recorder,

camcorder) has not been properly

connected.

Confirm that the source is properly

connected.

● All necessary power switches have not

been turned on.

Confirm that all units’ power switches are

turned on.

● The input mode is not correct. Set the input mode to “L-1”, “F-1”, “S-1”

or “S-2”.

4. Camcorder recording is not possible. ● The camcorder has not been properly

connected.

Confirm that the camcorder is properly

connected.

● The input mode is not correct. Set the input mode to “L-1”, “F-1”, “S-1”

or “S-2”.

5. The recorder automatically rewinds

the tape to the beginning.

● The end of the tape was reached during

recording.

The programme may not have been

recorded in its entirety. Next time make

sure you have enough time on the tape to

record the entire programme.

SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION

1. Timer recording won’t work. ● The clock and/or the timer have been set

incorrectly.

Re-perform the clock and/or timer

settings.

● The timer is not engaged. Press

and confirm that “

” is displayed

on the front display panel.

2. Timer programming is not possible. ● Timer recording is in progress. Timer programming can’t be performed

while a timer recording is in progress.

Wait until it finishes.

3. “

” on the front display panel won’t

stop blinking.

● The timer is engaged but there’s no

cassette loaded.

Load a cassette with the record safety tab

intact. If the tab has been removed, set

“REC SAFETY” to “OFF” (

墌

pg. 48).

4. “

”, “

䡬

” and “

” on the front

display panel won’t stop blinking.

● The loaded cassette has had its record

safety tab removed and “REC SAFETY”

is set to “ON”.

Set “REC SAFETY” to “OFF” (

墌

pg. 48),

or using adhesive tape, cover the hole

where the tab was removed.

● The end of the tape was reached during

timer recording.

The programme may not have been

recorded in its entirety. Next time make

sure you have enough time on the tape to

record the entire programme.

5. “

” blinks for 10 seconds and the

Timer mode is disengaged.

●

has been pressed when there are no

programs in memory, or the timer

record information has been

programmed incorrectly.

Check the programmed data and re-

program as necessary, then press

again.

6. The S

HOW

IEW

system does not

timer-record properly.

● The recorder’s channel positions have

been set incorrectly.

Refer to “Guide Program Number Set”

(

墌

pg. 49) and re-perform the procedure.

SR-V10E1-EN.book Page 60 Monday, August 19, 2002 10:20 AM

1 2 ... 55 56 57 58 59 60 61 62 63 64 65 66 67 68

Comments to this Manuals

No comments

JVC SR-V10E User Manual Page 60

Comments to this Manuals

Related products and manuals for Cassette players JVC SR-V10E