JVC RX-6500VBK User Manual download pdf (Page 17)

English

Digital Input (DIGITAL IN) Terminal

Setting

When you use the digital input terminals, you have to register what

components are connected to which terminals (DIGITAL IN 1/2/3).

Before you start, remember...

• There is a time limit in doing the following steps. If the setting is

canceled before you finish, start from step 1 again.

On the front panel ONLY:

1. Press SETTING repeatedly until

“DIGITAL IN” appears on the

display.

• Once you have pressed SETTING, MULTI

CURSOR % / ﬁ can be also used for

selecting “DIGITAL IN.”

• The display changes to show the current setting.

2. Press MULTI CURSOR @ / # to

select an appropriate setting.

• As you press it, the display changes to show

the following:

1 DVD 2 CD 3 DBS “ 1 DVD 2 CD 3 MD “

1 DVD 2 MD 3 DBS “ 1 CD 2 DVD 3 DBS “

1 CD 2 DVD 3 MD “ 1 CD 2 MD 3 DBS “

1 DBS 2 CD 3 DVD “ 1 DBS 2 CD 3 MD “

1 DVS 2 DVD 3 MD “ 1 MD 2 CD 3 DBS “

1 MD 2 CD 3 DVD “ 1 MD 2 DVD 3 DBS “

(back to the beginning)

Note:

When shipped from the factory, the DIGITAL IN terminals can be used

as the digital input for the following components.

• DIGITAL 1 (coaxial): For DVD player

• DIGITAL 2 (optical): For CD player

• DIGITAL 3 (optical): For DBS tuner

Selecting the Analog or Digital Input Mode

When you have connected some digital source components using the

digital terminals (see page 7), you need to change the input mode for

these components to the appropriate digital input mode correctly —

AUTO/PCM, DOLBY DIGITAL, or DTS.

Once the correct mode is selected for each digital source

component, the mode is memorized until you change it.

1. Follow the steps in “Digital Input (DIGITAL IN)

Terminal Setting” to the left.

2. Press the source selecting button (CD, TAPE/MD,

TV SOUND/DBS, or DVD) for which you want to

change the input mode from analog input to

digital input.

3. Press ANALOG/DIGITAL repeatedly until the

digital input mode you want appears on the

display.

Each time you press the button, the input mode changes as

follows:

Normally select “AUTO/PCM,” so the receiver automatically

detects the incoming digital signal. The DIGITAL AUTO

indicator lights up on the display. (The DIGITAL AUTO lamp

next to the ANALOG/DIGITAL button lights up.)

- When the receiver can recognize the digital signal coming

into the receiver, the frame of the digital signal indicator for

the detected signal lights up automatically.

- When the receiver cannot recognize the incoming signal

correctly, the frame of the digital signal indicator flashes.

If this happens, select the same digital input mode with the

incoming digital signal — either “DOLBY DIGITAL” or

“DTS.”

Notes:

• Noise may come out of the speakers while searching or skipping a

multi-sound source encoded with Dolby Digital or DTS Digital

Surround. If this happens, select “DOLBY DIGITAL” or “DTS” for

digital input mode. (See above)

• When you change the source, the digital input mode will be

automatically reset to “AUTO/PCM.”

SETTING

DIGITAL 2 terminal setting

DIGITAL 1 terminal setting DIGITAL 3 terminal setting

MULTI CURSOR

On the front panel

TV SOUND/ DBS

DVD

TAPE/MD

DVD

TV SOUND/DBS

TAPE/MD

SOURCE NAME

On the remote control

DIGITAL AUTO

ANALOG/DIGITAL

On the front panel On the remote control

ANALOG

DTS

AUTO/PCM

DOLBY DIGITAL

(Digital)

(Digital)(Digital)

EN08_17.RX-6500V[J] 99.12.16, 1:08 PM14

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 40 41

Comments to this Manuals

No comments

JVC RX-6500VBK User Manual Page 17

Comments to this Manuals

Related products and manuals for AV receivers JVC RX-6500VBK