JVC RX-F10S User Manual download pdf (Page 19)

Basic operations

Turning off the sounds temporarily

From the remote control ONLY:

Press MUTING to turn off the sound through all

connected speakers and headphones connected.

“MUTING” appears on the display and the volume turns off.

To restore the sound, press MUTING again.

• Pressing VOLUME +/– (or turning MASTER VOLUME control

on the front panel) also restores the sound.

Changing the display brightness

You can dim the display—Dimmer.

From the remote control ONLY:

Press DIMMER repeatedly.

• Each time you press the button, the display brightness changes

as follows:

DIMMER 1: Dims the display slightly.

Dims the blue illumination slightly.

DIMMER 2: Dims the display more than DIMMER 1.

Dims the blue illumination slightly (same as

DIMMER 1).

DIMMER 3: Turns off the display and blue illumination.

(Temporarily canceled when you operate the

receiver.*)

DIMMER OFF: Cancels the Dimmer (normal display).

* Except when activating or deactivating TV Direct.

Turning off the power with the Sleep

Timer

You can fall asleep while listening to music—Sleep Timer.

From the remote control ONLY:

Press SLEEP repeatedly.

• Each time you press the button, the shut-off time changes in 10

minute intervals. The SLEEP indicator lights up on the display.

SLEEP indicator

When the shut-off time comes:

The receiver turns off automatically.

To check or change the remaining time until the shut-off

time:

Press SLEEP once.

The remaining time (in minutes) until the shut-off time appears.

• To change the shut-off time, press SLEEP repeatedly.

LPCM L

LS SB RS

S . WFR

NEO : 6

DSP 3D

LFE

C R

DOLBY D

DTS AAC

96 / 24

AUTO SR

C.TONE VIRTUAL SB AUDIO P. BASS TA NEWS INFO RDS TUNED ST SLEEP

AUTO MUTING AUTO MODE

ATT

MHz

kHz

LPCM L

LS SB RS

S . WFR

NEO : 6

DSP 3D

LFE

C R

DOLBY D

DTS AAC

96 / 24

AUTO SR

C.TONE VIRTUAL SB AUDIO P. BASS TA NEWS INFO RDS TUNED ST SLEEP

AUTO MUTING AUTO MODE

ATT

MHz

kHz

10 20 30 40 50 60

90OFF (canceled) 80 70

LPCM L

LS SB RS

S . WFR

NEO : 6

DSP 3D

LFE

DOLBY D

DTS AAC

96 / 24

AUTO SR

C.TONE VIRTUAL SB AUDIO P. BASS TA NEWS INFO RDS

LS SB RS

S . WFR LFE

CRL

LS SB RS

S . WFR LFE

To cancel the Sleep Timer:

Press SLEEP repeatedly so that “SLEEP OFF” appears on the

display. (The SLEEP indicator goes off.)

• The Sleep Timer is also canceled when:

– You turn off the receiver, or

– TV Direct is activated.

Basic adjustment of auto memory

This receiver memorizes sound settings for each source:

• when you turn off the power, and

• when you change the source.

When you change the source, the memorized settings for the

newly selected source are automatically recalled.

The following can be stored for each source:

• Analogue/digital input mode (see page 12)

• Speaker output level (see page 23)

• Subwoofer audio position (see page 14)

• Subwoofer phase (see page 24)

• Digital equalization pattern (see page 24)

• Bass boost (see page 24)

• Input attenuator mode (see page 24)

• Surround/DSP mode selection (see pages 34 and 35)

NOTE

If the source is FM or AM (MW), you can assign a different

setting for each band.

Signal and speaker indicators on the display

Signal indicators Speaker indicators

The signal indicators light up as follows:

L: • When digital input is selected: Lights up when the

left channel signal comes in.

• When analogue input is selected: Always lights up.

R: • When digital input is selected: Lights up when the

right channel signal comes in.

• When analogue input is selected: Always lights up.

C: Lights up when the center channel signal comes in.

LS*: Lights up when the left surround channel signal comes

in.

RS*: Lights up when the right surround channel signal comes

in.

SB: Lights up when the surround back channel signal

comes in.

LFE: Lights up when the LFE channel signal comes in.

* When monaural surround signal comes in, only “S” lights up.

NOTE

When “DVD MULTI” is selected as the source, all the signal

indicators except “SB” light up.

The speaker indicators light up as follows:

• The subwoofer indicator (

S . WFR

) lights up when

“SUBWOOFER” is set to “SUBWFR :YES.” For details, see

page 18.

• The other speaker indicators light up only when the

corresponding speaker is set to “SML (small)” or “LRG

(large),” and also when required for the current playback.

12-15RX-F10[B]_f.p65 04.2.13, 16:4015

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 46 47

Comments to this Manuals

No comments

JVC RX-F10S User Manual Page 19

Comments to this Manuals

Related products and manuals for AV receivers JVC RX-F10S