JVC RX-F10S User Manual download pdf (Page 18)

Basic settings

To obtain the best possible sound effect from Surround/DSP

modes (see pages 27 to 31), you need to set up the speaker and

subwoofer information after all the connections are completed.

From pages 16 to 21, how to set speakers and other basic items

of the receiver are explained.

Setting the speaker information

automatically—Smart Surround Setup

The distance from your listening point to the speakers is one of

the important elements to obtain the best possible sound effect for

the Surround/DSP modes.

By using Smart Surround Setup, the following are automatically

calculated by one simple action—clapping hands.

• Speaker distance (compared to that of the closest speaker)

• Speaker output level (except the subwoofer)

NOTES

•To set the speaker information effectively using Smart Surround

Setup, unplug the power cords of all the components connected

to this receiver and the subwoofer which may cause noise.

• Before starting Smart Surround Setup, set the speaker

information correctly (SML, LRG, or NO) according to your

speakers except the subwoofer (see page 18).

• When the setting is made by Smart Surround Setup, the

speaker distance and output level you have set before will be

inactive.

• If you have turned off the display, cancel the Dimmer (see page

15); otherwise, you cannot see the information on the display

during Smart Surround Setup.

• Smart Surround Setup will not be done correctly if you or other

object blocks the sound.

• When you change your speakers, do the following procedure

again.

From the remote control ONLY:

Press and hold SMART SURROUND SETUP

until “SETTING UP” flashes on the display.

Confirm that “SETTING UP” stops flashing,

then clap your hands over your head once

while “SETTING UP” still remains on the

display.

The receiver starts detecting the level of the sound coming

through each speakers (except the subwoofer).

When your clapping sound is detected successfully,

“SUCCESSFUL” appears on the display, then the values set are

shown as follows:

Ex.:

Then the receiver returns to

normal operation mode.

*1 Standard channel (the closest speaker).

This speaker position now works as the reference

position (“0m/ft”) and other speakers’ distance is

shown by the difference with this reference speaker

position.

*2 L: Left front speaker

R: Right front speaker

C: Center speaker

LS: Left surround speaker

RS: Right surround speaker

SB: Surround back speaker

*3 Difference of each speaker position in distance (in

meters or feet).

*4 Each speaker’s output level (–6 to +6).

When your clapping sound is not detected correctly,

“SETTING UP” appears again after one of the following

messages. In this case, repeat step

SILENT: • The receiver detects sound from only the left

and right front speakers.

• The receiver detects no sound from the front

speakers and detects sound from at least one of

the other speakers.

SILENT-ALL: The receiver cannot detect any sound from any

speakers for about 15 seconds.

FAILED: The receiver cannot detect sound from the left or

right front speaker.

Take your position where you listen to the

sound.

• Make sure speaker cables are connected firmly.

Basic settings

When operating the receiver

using the remote control, set

the mode selector to

“AUDIO/TV/VCR/DBS.”

LPCM L

LS SB RS

S . WFR

NEO : 6

DSP 3D

LFE

C R

DOLBY D

DTS AAC

96 / 24

AUTO SR

C.TONE VIRTUAL SB AUDIO P. BASS TA NEWS INFO RDS TUNED ST SLEEP

AUTO MUTING AUTO MODE

ATT

MHz

kHz

*3*2

LS RS SB

16-21RX-F10S[J]_f.p65 04.4.22, 15:2516

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 ... 87 88

Comments to this Manuals

No comments

JVC RX-F10S User Manual Page 18

Comments to this Manuals

Related products and manuals for AV receivers JVC RX-F10S