JVC RX-F10S User Manual download pdf (Page 15)

Basic operations

Adjust the volume

To increase the volume, turn MASTER VOLUME

control clockwise (or press VOLUME + on the

remote control).

To decrease the volume, turn MASTER VOLUME

control counterclockwise (or press VOLUME – on

the remote control).

• When you adjust the volume, the volume level indication

appears on the display for a while.

CAUTION:

Always set the volume to the minimum before starting any

sources. If the volume is set at its high level, the sudden blast of

sound energy can permanently damage your hearing and/or ruin

your speakers.

NOTE

The volume level can be adjusted within the range of “0” (minimum)

to “50” (maximum).

Listening with headphones

You can enjoy not only stereo software but also multi-channel

software through the headphones. (Sounds are down-mixed to the

front channels while playing multi-channel software.)

Connect a pair of headphones to the PHONES jack on the

front panel to activate the HEADPHONE mode.

The HP (headphone) indicator lights up on the display.

•You can also enjoy the Surround/DSP mode through the

headphones—3D HEADPHONE mode. For details, see pages

28 and 29.

• Disconnecting a pair of headphones from the PHONES jack

cancels the HEADPHONE (or 3D HEADPHONE) mode and

activates the speakers.

CAUTION:

Be sure to turn down the volume:

• Before connecting or putting on headphones, as high volume

can damage both the headphones and your hearing.

• Before removing headphones, as high volume may output from

the speakers.

Selecting the digital decode mode

If the following symptoms occur while playing Dolby Digital or DTS

software with “DGTL AUTO” selected (see page 12), follow the

procedure below:

• Sound does not come out at the beginning of playback.

• Noise comes out while searching for or skipping chapters or

tracks.

From the remote control ONLY:

Press SOUND, then press DECODE to select

“DGTL D.D.” or “DGTL DTS.”

• Each time you press DECODE, the digital decode mode

changes as follows:

•To play back software encoded with Dolby Digital, select

“DGTL D.D.”

•To play back software encoded with DTS, select “DGTL DTS.”

NOTES

• When you turn off the power or select another source,

“DGTL D.D.” or “DGTL DTS” is canceled and the digital decode

mode is automatically reset to “DGTL AUTO.”

• After pressing SOUND, the numeric buttons work for sound

adjustments. To use the numeric buttons to operate your target

source, press the corresponding source selecting button before

operation; otherwise, the remote control may not work as you

intend.

The following digital signal format indicators on the display

indicate what type of signal comes into the receiver.

LPCM: Lights up when Linear PCM signal comes in.

DOLBY D: • Lights up when Dolby Digital signal comes in.

• Flashes when “DGTL D.D.” is selected for any

software other than Dolby Digital.

DTS: • Lights up when conventional DTS signal comes

in.

• Flashes when “DGTL DTS” is selected for any

software other than DTS.

DTS 96/24: Lights up when DTS 96/24 signal comes in.

NOTE

When “DGTL AUTO” cannot recognize the incoming signal, no

digital signal format indicator lights up on the display.

LPCM L

LS SB RS

S . WFR

NEO : 6

DSP 3D

LFE

C R

DOLBY D

DTS AAC

96 / 24

AUTO SR

C.TONE VIRTUAL SB AUDIO P. BASS TA NEWS INFO RDS TUNED ST SLEEP

AUTO MUTING AUTO MODE

ATT

MHz

kHz

LPCM L

LS SB RS

S . WFR

NEO : 6

DSP 3D

LFE

DOLBY D

DTS AAC

96 / 24

AUTO SR

C.TONE VIRTUAL SB AUDIO P. BASS TA NEWS INFO RDS TUNED ST SLEEP

AUTO MUTING AUTO MODE

ATT

MHz

kHz

DGTL AUTO

DGTL D.D.

DGTL DTS

(Back to the beginning)

12-15RX-F10S[J]_f.p65 04.4.22, 15:2513

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 87 88

Comments to this Manuals

No comments

JVC RX-F10S User Manual Page 15

Comments to this Manuals

Related products and manuals for AV receivers JVC RX-F10S