JVC RX-DP15BC User Manual download pdf (Page 41)

English

1 Setting the Speakers—SPEAKER SETTING

To obtain the best possible

surround sound of the Surround/

THX/DSP modes in Zone 1, you

have to register the information

about the speaker arrangement

after all connections are

completed.

SUBWOOFER

YES : Select when a subwoofer is connected.

NO : Select when no subwoofer is used.

FRONT SP, CENTER SP, SURROUND SP,

SURR BACK SP

speakers, center speaker, surround speakers, and surround back

speakers.

LARGE : Select when the speaker size is relatively large.

SMALL : Select when the speaker size is relatively small.

NONE : Select when you have not connected a speaker. (Not

selectable for the front speakers.)

Notes:

• Keep the following comment in mind as reference when

adjusting:

– If the size of the cone speaker unit built in your speaker is

greater than 12 cm, select “LARGE,” and if it is smaller than

12 cm, select “SMALL.”

• If you have selected “NO” for the subwoofer, you can only

select “LARGE” for the front speakers.

• If you have selected “SMALL” for the front speakers, you

cannot select “LARGE” for the center, surround, and surround

back speakers.

• If you have selected “SMALL” for the surround speakers, you

cannot select “LARGE” for the surround back speakers.

• If you have selected “NONE” for the surround speakers, the

surround back speakers are fixed to “NONE.”

SURR BACK OUT

you can use only one unit or a pair of the units for your surround

back sounds.

1SPK : Select when only one speaker is connected for your

surround back sounds—minimum requirement for

THX Surround EX (see page 51).

2SPK : Select when a pair of speakers are connected for

your surround back sounds—requirement for THX

Ultra2 Cinema and THX Music (see page 51).

CROSSOVER

You can select the crossover frequency for the small speakers

used. The signals below the preset frequency level will be sent to

and be reproduced by the subwoofer (or by “LARGE” speakers

when “SUBWOOFER” is set to “NO”).

Select one of the crossover frequency levels according to the

size of the small speaker connected:

80Hz : Select when the cone speaker unit built in the

speaker system is about 12 cm.

• When using the THX-certified speakers, the

crossover frequency should be set to “80 Hz.”

100Hz : Select when the cone speaker unit built in the

speaker system is about 10 cm.

120Hz : Select when the cone speaker unit built in the

speaker system is about 8 cm.

Notes:

• Use the above comments as reference when adjusting.

If you have selected “LARGE” for all activated speakers, this

function will be set to “OFF.”

• Crossover frequency is not valid for “HEADPHONE” and “3D

HEADPHONE.”

• If Analog Direct is in use, this function does not take effect.

2 Adjusting the Speaker Channel Output

Levels—CHANNEL LEVEL

On this submenu, you can adjust

the speaker channel output

levels. While transmitting the

test tone, select a speaker

channel and adjust its output

level.

Note:

You can show this submenu simply by pressing TEST (after pressing

SOUND) on the remote control. The test tone comes out of the

activated speakers in sequence.

Adjustment procedure on this submenu

Adjustment is also possible without emitting the test tone. In this

case, you can skip steps 1, 2, and 6 below.

• You can only adjust the activated speakers on the SPEAKER

SETTING submenu (see the left column). The test tone will

not come out of the deactivated speakers.

1 Press ﬁ or % (DOWN or UP) to select “TEST TONE.”

2 Press # or @ (RIGHT or LEFT) to output the test tone.

(See “TEST TONE” on the next page.)

3 Press ﬁ or % (DOWN or UP) to select a speaker you want

to adjust.

4 Press # or @ (RIGHT or LEFT) to adjust the speaker output

level.

5 Repeat steps 3 and 4 to adjust the other speaker output

levels.

6 After adjustment is finished, stop the test tone.

1 Press % (UP) to select “TEST TONE.”

2 Press # or @ (RIGHT or LEFT) to select “OFF.”

Continued on the next page.

:OPERATE

:BACK

SPEAKER SETTING

SUBWOOFER : NO

FRONT SP : LARGE

CENTER SP : SMALL

SURROUND SP : SMALL

SURR BACK SP : SMALL

SURR BACK OUT: 2SPK

CROSSOVER : 80Hz

:OPERATE :BACK

CHANNEL LEVEL

TEST TONE :OFF

FRONT L LEVEL: 0dB

CENTER LEVEL: 0dB

FRONT R LEVEL: 0dB

SURR R LEVEL: 0dB

SBACK R LEVEL: 0dB

SBACK L LEVEL: 0dB

SURR L LEVEL: 0dB

SUBWOOFER : 0dB

35-44_RX-DP15B[C]f.pm6 04.4.14, 3:08 PM38

1 ... 40 41 42 ... 173

Comments to this Manuals

No comments

JVC RX-DP15BC User Manual Page 41

Comments to this Manuals

Related products and manuals for AV receivers JVC RX-DP15BC