Jvc RX-6010RBK EN User Manual download pdf (Page 16)

T SETTING

CONTROL

DOWN UP

Crossover Frequency Setting

Small speakers cannot reproduce the bass sound very well. So, if

you have used a small speaker for any of the front, center, and rear

channels, this receiver automatically reallocates the bass elements,

originally assigned to the channel for which you have connected the

small speaker, to another channel (for which you have connected the

large speaker).

If you have selected “LARGE” for all speakers (see page 12), this

function will not take effect. To use this function properly, you need

to set this crossover frequency level according to the size of the

small speaker connected.

On the front panel ONLY:

1. Press SETTING repeatedly until

“CROSSOVER FRQ” (Crossover

Frequency) appears on the display.

The display changes to show the current setting.

2. Press CONTROL UP 5/DOWN ∞

to select the crossover frequency

level according to the size of the

small speaker connected.

• Each time you press the button, the display

changes to show the following:

• Use the following comments as reference when adjusting.

80HZ: Select this when the cone speaker unit built in the

speaker is about 4

/4 inches (12 cm).

100HZ: Select this when the cone speaker unit built in the

speaker is about 3

/16 inches (10 cm).

120HZ: Select this when the cone speaker unit built in the

speaker is about 3

/16 inches (8 cm).

Note:

Crossover frequency is not valid for the HEADPHONE mode.

SETTING

CONTROL

DOWN UP

80HZ

100HZ 120HZ

0dB 10dB

Low Frequency Effect Attenuator Setting

If the bass sound is distorted while playing back a source using

Dolby Digital or DTS Digital Surround, follow the procedure below.

On the front panel ONLY:

1. Press SETTING repeatedly until

“LFE ATT” (Low Frequency

Effect Attenuator) appears on the

display.

The display changes to show the current setting.

2. Press CONTROL UP 5/DOWN ∞

to select the low frequency effect

attenuator level.

• Each time you press the button, the display

changes to show the following:

0dB: Normally select this.

10dB: Select this when the bass sound is distorted.

Note:

This function takes effect only when the subwoofer (LFE) signals

come in, (with “SUBWOOFER” set to “YES.”)

Dynamic Range Compression Setting

You can compress the dynamic range (difference between maximum

sound and minimum sound) of the reproduced sound. This is useful

when enjoying surround sound at night.

• This function takes effect only when playing back a source using

Dolby Digital.

On the front panel ONLY:

1. Press SETTING repeatedly until

“D_RANGE COMP” (Dynamic

Range Compression) appears on

the display.

The display changes to show the current setting.

2. Press CONTROL UP 5/DOWN ∞

to select the appropriate item

about the compression level.

• Each time you press the button, the

display changes to show the following:

OFF: Select this when you want to enjoy surround with its

full dynamic range. (No effect applied.)

MID: Select this when you want to reduce the dynamic

range a little. (Factory setting.)

MAX: Select this when you want to apply the compression

effect fully. (Useful at night.)

Note:

Dynamic Range Compression is not valid for the DTS Digital

Surround.

OFF MID MAX

CONTROL

DOWN UP

SETTING

EN08-20.RX-6010&6012R[B]_f 01.1.9, 6:39 PM13

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 ... 35 36

Comments to this Manuals

No comments

Jvc RX-6010RBK EN User Manual Page 16

Comments to this Manuals

Related products and manuals for Receivers and Amplifiers Jvc RX-6010RBK EN