For Customer Use:Enter below the Serial No. which is located onthe body.Retain this information for future reference.Model No.Serial No.Thank you for
10IntroductionCamera unitAMounting hole (elliptical) ⳯ 4Use these when mounting the camera to the electrical box.(A Pg. 22)B Mounting hole (round) ⳯ 4
11Camera unit/Inside the cameraT This is when the dome cover, inner cover and outer case is removed.How to remove ( A Pg. 17 eMounting on a ceilingf S
12IntroductionInside the cameraQCeiling Mount Bracket (x3)This serves as a bracket when embedding the camera in a ceiling. (A Pg. 17)R Camera Fastenin
13Lens sectionZ [FOCUS ADJ] Focus adjustment buttonThis is used to adjust the lens focus.Press the button to open the lens Iris for 30 seconds. The fo
14IntroductionMonitoring Via Built-in ViewerVN-C215V4U comes with a built-in ActiveX viewer.Monitoring of VN-C215V4U images using the computer is poss
15Restrictions on ClientsIt is possible for VN-C215V4U to permit or deny image acquisition of designated IP addresses.Control via customized applicati
16SetupThe connection and setup procedures are described as below. K K KBefore MountingNote:
17Selecting Mounting MethodThe procedures differ according to the mounting method. Check the respective items before mounting.Note:
18SetupMounting on a ceiling (continued)4.Remove the inner dome.The inner dome is secured by 3 clips. Remove the inner dome from the clips.5.Remove th
19䡵 Mounting1.Face the imaging direction mark (j) in the shooting direction and mount the camera.2.Secure the camera in 3 locations.A Use a cross slot
2IntroductionSafety Precautions1. Read all of these instructions.2. Save these instructions for later use.3. All warnings on the product and in the op
20SetupMounting the camera directly on a ceiling or alongside a wallTo mount on a wall, use the same procedures below but replace the word “ceiling” w
214.Connect the LAN cable. (A Pg. 26)5.Connect the power cable and the alarm cable. (A Pg. 24)Memo:
22SetupMount by allowing the cable to exit from the sideYou can also mount the camera on a ceiling or wall by pulling the cables horizontally instead
23䡵 MountingAttach the camera to the outer case that has been fastened to the electrical box.1.Follow steps 2 to 6 of AMount by allowing the cable to
24SetupElectricity can be supplied to this product either by using the PoE or connecting to the DC12 V power supply.䢇 When electricity is supplied to
25Connecting to the DC12 V power supplyConnect this product to the DC12 V power supply when not using the PoE.Connect the polarity correctly.Note:
26SetupConnect the camera to a hub or computer using a LAN cable.䡵 When connecting to a hubMake use of a straight cable.䡵 When connecting to a compute
27Alarm InputConnect this terminal to sensor devices, such as an infrared sensor, door sensor, metal sensor, manual switch, etc.䡵 Input requirements●
28SetupAdjusting the camera shooting directionThis camera can be adjusted for pan, tilt and rotation. Adjust the direction and face the camera towards
29Field angle adjustmentLoosen the fastening screw of the zoom adjustment ring, move the ring horizontally and adjust the image size.Focus adjustmentP
3Information for USAThis device complies with part 15 of the FCC Rules.Changes or modifications not approved by JVC couldvoid the user's authorit
30Setting● Ensure that there is sufficient network bandwidth for the data volume to be sent out by VN-C215V4U.● Data volume to be sent by VN-C215V4U v
31Setting IP address with the default VN-C215V4U settingsThere are 2 methods to set the IP address when VN-C215V4U is in its default settings.(A) Assi
32Setting䢇 IP Address setting at the computerSet the computer to an IP address that enables communication with VN-C215V4U.1.Click [Start]● Select in t
33䢇 Changing the IP address using the Internet Explorer1.Launch the Internet Explorer on the computer2.When proxy setting is enabled in the Internet E
34Setting䢇 Changing the IP address using the Internet Explorer (continued)4.Launch the Internet ExplorerMemo:
356.The top page of VN-C215V4U appears7.The Basic page with the IP address settings appearsA confirmation screen appears. Press the [OK] button. The V
36SettingWhen the IP address of VN-C215V4U is knownWhen the IP address of VN-C215V4U is known, it can be changed by using Internet Explorer on the com
37OperationUsing the built-in viewer enables display of a series of images, one-shot recording of images and receiving of alarm information.⽧Setting U
38OperationSetting Up the Internet Explorer1.Launch the Internet Explorer on the computer2.When proxy setting is enabled in the Internet Explorer, fol
393.If Active X controls and plug-ins of the Internet Explorer is disabled, follow the steps below to enable it● Click [Trusted sites] under [Tools]-[
4IntroductionSafety Precautions (continued)Information for Users on Disposal of Old Equipment[European Union]This symbol indicates that the electrical
40OperationInstalling the built-in viewer1.Enter the URL of the built-in viewer in the address field of Internet ExplorerFor example, if the IP addres
41Screen Configuration of Built-in Viewer● VN-C215V4U is set to encode at 15 fps by default.A Alarm Appears blinking when alarm packets are sent from
42OperationQuitting the Built-in ViewerTo quit, press the [Close] button at the top right of the window.● To restart the built-in viewer, launch the I
43Shortcut for Built-in ViewerCreating a shortcut for the built-in viewer on the Desktop screen of the computer saves you the trouble of having to ent
44OthersCamera Unit[Monitor Output]Monitor output x 1 (75, 1 Vp-p)[Network Output]LAN SpecificationsCompliant with IEEE802.3, IEEE802.3u and IEEE802.3
45Dimension [Unit: mm(inches)]T Specifications and appearance of this unit and related products are subject to change for product improvement without
46VN-C215_EN.book Page 46 Monday, November 27, 2006 9:52 AM
47VN-C215_EN.book Page 47 Monday, November 27, 2006 9:52 AM
© 2006 Victor Company of Japan, LimitedLST0527-001AVN-C215V4UFIXED IP DOME CAMERAVN-C215_EN.book Page 48 Monday, November 27, 2006 9:52 AM
5● This installation should be made by a qualified service person and should conform to all local codes.● This installation shall be in accordance wit
6Introduction䡵 High Picture QualityThe camera unit of VN-C215V4U employs a 380,000-pixel CCD (1/4") which enables high quality image monitoring.䡵
7IntroductionSafety Precautions ... 2Main Features ... 6Contents ...
8Introduction䡵 PC Specification Requirements䡵 LAN Environment● 10BASE-T/100BASE-TX network interconnected using an IEEE802.3-compliant switching hub.●
9Others䢇 This product has a built-in AGC circuit. When AGC is AOnB, the product sensitivity increases automatically at dark places and the image on th
Comments to this Manuals