Jvc UX-GP5 User Manual download pdf

INSTRUCTIONS

GVT0242-019B[J/C]

0108WMKMDWJMM

2 4

Connections

Basic and Common Operations

Supplied Accessories

After unpacking, check to be sure that you have all the

following items.

• Remote control, RM-SUXGP5A (× 1)

• Lithium coin battery CR2025 (× 1)

– The battery has been installed when shipped from the

factory.

• AM loop antenna (× 1)

• FM antenna (× 1)

If anything is missing, consult your dealer immediately.

Prepare the Remote Control

When you use the remote control for the first time, pull out

the insulation sheet.

To Replace the Battery in the Remote Control

NOTES:

• Store the battery in a place where children cannot reach. If

a child accidentally swallows the battery, consult a doctor

immediately.

• To prevent the battery from over-heating, cracking, or starting

a fire:

– Do not recharge, short, disassemble or heat the battery or

dispose of it in a fire.

– Do not leave the battery with other metallic materials.

– Wrap the battery with tape and insulate when throwing

away or saving it.

– Do not poke the battery with tweezers or similar tools.

• Dispose of battery in the proper manner, according to federal,

state, and local regulations.

• The batteries (battery pack or batteries installed) shall not be

exposed to excessive heat source such as sunshine, fire or the

like.

Basic Disc Operations

To Press Indication/Result

Play back the disc

• Current track number and elapsed playing

time appear.

For MP3/WMA files: Before current track

number and elapsed playing time appear, the

tag information appears if it is recorded.

• During playback, press again to pause.

Stop playback

• While playback is stopped, total track number

and total playing time (for MP3/WMA files,

group number and track number) appear.

Select a track

Select the next tracks.

To go back to the beginning of the current or

previous tracks.

Select a group

(MP3/WMA only)

Select the next groups.

Select the previous groups.

Forward search/

Reverse search

Press and hold to fast-forward the track during

playback.

To stop searching, release the button.

Press and hold to fast-reverse the track during

playback.

To stop searching, release the button.

NOTES:

• If no disc is inserted, “NO DISC” appears on the main display.

• If MP3/WMA files are not recorded on the disc, “NO PLAY” appears on the main

display.

Playing Repeatedly—Repeat Play

Press repeatedly to specify the repeat mode as follows:

REP TRK: Repeats the current (or specified) track. [ ]

REP GRP: Repeats all tracks in the current group (MP3/WMA

only). [ ]

REP ALL: Repeats all tracks. [ ALL ]

REP OFF: Normal playback

Getting Started

Playing Back a Disc

MICRO COMPONENT SYSTEM

UX-GP5

—Consists of CA-UXGP5 and SP-UXG300

This System can play back...

– CD.

– CD-R/CD-RW recorded in audio CD format (CD-DA) or recorded MP3/WMA files

in ISO 9660 format.

• When playing back an MP3 or WMA track, MP3 or WMA indicator lights up.

Loading a Disc (on the System only)

Press to open the disc tray.

• When using an 8 cm disc, place it on the inner

circle of the disc tray.

Press to close the disc tray.

Prohibiting Disc Ejection (on the System only)

You can lock the disc tray so that no one can eject the loaded disc.

• This is possible while the System is on standby.

To cancel the prohibition, repeat the same procedure.

Programming the Playing Order—Program Play

During stops, press until the PRGM (program) indicator lights up

before playing.

• For MP3/WMA files: Select a group number, then a track

number.

• For CD: Select a track number.

Press to program the selected group/track.

Repeat steps 2 and 3 to program other tracks you want.

• If you try to program a 51st track, “FULL” will appear.

The tracks are played back in the programmed order.

Operations for Program Play (while not playing)

• To check the programmed contents, press 4 or ¢.

• To add tracks, repeat steps 2 and 3 above.

• To erase the last programmed track, press CANCEL.

• To erase the entire program, press and hold CANCEL for about 2 seconds.

• To exit from program play, press MODE.

– The stored program is kept.

Playing at Random—Random Play

Press until the RND (random) indicator lights up before you start

playback.

Playback starts in random order.

Random Play ends when all tracks are played back.

Operations for Random Play

• To skip a track, press ¢.

• To go back to the beginning of the current track, press 4.

• To exit from random play, press MODE while playback is stopped.

Thank you for purchasing a JVC product.

Lithium coin battery

(product number: CR2025)

Insulation sheet

Press

Indication/Result

System Remote

Turn on or off

(standby) the power

The STANDBY lamp on the System turns off/on.

Select a source

See “Playing Back a Disc” on page 4 and “Listening to an

iPod” on page 5.

Press repeatedly to select “FM” or “AM.”

• For “FM/AM,” see “Listening to FM and AM

Broadcasts” on page 5.

See “Listening to Digital Audio Player” on page 5.

Adjust the volume

Adjustable range: Level 0 (“VOL MIN”) to level 40

(“VOL MAX”).

Drop the volume in a

moment

—

To restore the volume, press again, or adjust the

volume level.

Activate the EALA

surround mode —

The indicator lights up.

To cancel this function, press repeatedly until

indicator lights off.

Emphasize the

sound (Sound Turbo

function)

The S.TURBO indicator lights up.

To cancel this function, press again.

Reinforce the bass

sound (Active Hyper

Bass Pro function) —

Press and hold until the AHB indicator lights up.

• When Sound Turbo function is activated (see above),

this function cannot be activated.

To cancel this function, press and hold again when

Sound Turbo function is deactivated.

Adjust the tone

(Bass/Treble)

—

Press once for adjusting the bass level; twice for treble

level, then, press VOLUME +/–.

Adjustable range: –3 to +3.

Change the display

brightness

—

You can dim the display window and illumination lamp.

While the System is turned on...

Change the display

information (Clock

and Source)

—

For setting the clock, see “Setting the Clock and Using

Timers” on page 6.

Set the Save Mode

—

Press when the System is on standby.

Setting the save mode allows you to reduce power

consumption by turning the display off while on

standby.

To cancel this function, press again when the System

is on standby.

NOTE:

DO NOT turn off (standby) the System with the volume set to an extremely high level;

otherwise, the sudden blast of sound can damage your hearing, speakers and/or

headphones when you turn on the System or start playback.

To a wall outlet

Plug the AC power cord only after all connections are complete.

Rear view

Outdoor FM antenna

(not supplied)

Disconnect the supplied FM antenna, and connect

to an outdoor FM antenna using a 75 Ω wire with

coaxial type connector (IEC or DIN45325).

FM antenna (supplied)

AM loop antenna (supplied)

Turn it until the best reception

is obtained.

RESUME Play (For MP3/WMA only)

When you stop the playback by one of the following operations, this System

stores the beginning of the stopped track on the disc.

– Pressing 7 once

– Changing the source

When you start playback again, playback starts from the stored position.

To clear the stored position, open the disc tray.

• When you clear the stored position and start playback, playback starts from the

beginning of the first track.

NOTE:

This function does not work in Program Play and Random Play.

The following operations are explained using the remote control, unless

mentioned otherwise. However, if the System has the same or similar button

names, they can also be used for the operations.

CAUTION:

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type.

NOTES:

• Make sure the antenna conductors do not touch any other terminals, connecting cords and power cord. Also, keep the antennas

away from metallic parts of the System, connecting cords, and the AC power cord. This could cause poor reception.

• Make sure both the speakers are connected correctly and firmly.

• When connecting the speaker cords, match the polarity of the speaker terminals: red color to (+) and black color to (–).

• DO NOT connect more than one speaker to each terminal.

• DO NOT allow the conductor of the speaker cords to be in touch with the metallic parts of the System.

Do not connect the AC power cord until all other connections have been made.

To connect the FM antenna (supplied)

Extend it so that you can obtain the best reception.

For better FM reception

To connect the AM loop antenna (supplied) To assemble the AM loop antenna

To connect the speaker cords

Using Headphones

Be sure to turn down the volume before connecting or putting on the headphones.

• Connecting the headphones will deactivate the speakers.

• Sound adjustments also affect the sound through the headphones.

Press and hold

Insert

Release

Red

Black

From left

speaker

From right

speaker

Point at the remote sensor on the front panel.

(The operating range is approx. 7 m.)

STANDBY lamp

PHONES jack

Stereo mini plug cord

For customer use:

Enter below the Model No. and Serial No. which are

located either on the rear, bottom or side of the cabinet.

Retain this information for future reference.

Model No.

Serial No.

Warnings, Cautions and Others

Mises en garde, précautions et indications

diverses

The lightning flash with arrowhead symbol,

within an equilateral triangle is intended to

alert the user to the presence of uninsulated

“dangerous voltage” within the products

enclosure that may be of sufficient magnitude

to constitute a risk of electric shock to persons.

The exclamation point within an equilateral

triangle is intended to alert the user to

the presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

Note to CATV system installer:

This reminder is provided to call the CATV system

installer’s attention to Section 820-40 of the NEC which

provides guidelines for proper grounding and, in particular,

specifies that the cable ground shall be connected to the

grounding system of the building, as close to the point of

cable entry as practical.

For U.S.A.

This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to part 15 of

the FCC Rules.

These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that

interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or

television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following

measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and

receiver. Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician

for help.

Le symbole de l’éclair à l’intérieur d’un triangle

équilatéral est destiné à alerter l’utilisateur sur

la présence d’une “tension dangereuse” non

isolée dans le boîtier du produit. Cette tension

est suffisante pour provoquer l’électrocution

de personnes.

Le point d’exclamation à l’intérieur d’un

triangle équilatéral est destiné à alerter

l’utilisateur sur la présence d’opérations

d’entretien importantes au sujet desquelles

des renseignements se trouvent dans le

manuel d’instructions.

IMPORTANT FOR LASER PRODUCTS

1. CLASS 1 LASER PRODUCT

2. CAUTION: Do not open the top cover or cabinet. There

are no user serviceable parts inside the unit; leave all

servicing to qualified service personnel.

3. CAUTION: Visible and/or invisible class 1M laser radiation

when open. Do not view directly with optical instruments.

4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED

INSIDE THE UNIT.

IMPORTANT POUR PRODUITS LASER

1. PRODUIT LASER CLASSE 1

2. ATTENTION: N’ouvrez pas le couvercle supérieur ni

le coffret de l’appareil. Il n’y a aucune pièce réparable

par l’utilisateur à l’intérieur de l’appareil; confiez toute

réparation à un personnel qualifié.

3. ATTENTION: Rayonnement laser visible et/ou invisible

de classe 1M une fois ouvert. Ne pas regarder directement

dans le faisceau avec des instruments optiques.

4. REPRODUCTION DE L’ÉTIQUETTE: ÉTIQUETTE DE

PRÉCAUTION PLACÉE À L’INTERIEUR DE L’APPAREIL.

For Canada/pour le Canada:

THIS DIGITAL APPARATUS DOES NOT EXCEED THE CLASS

B LIMITS FOR RADIO NOISE EMISSIONS FROM DIGITAL

APPARATUS AS SET OUT IN THE INTERFERENCE-CAUSING

EQUIPMENT STANDARD ENTITLED “DIGITAL APPARATUS,”

ICES-003 OF THE DEPARTMENT OF COMMUNICATIONS.

CET APPAREIL NUMERIQUE RESPECTE LES LIMITES DE

BRUITS RADIOELECTRIQUES APPLICABLES AUX APPAREILS

NUMIRIQUES DE CLASSE B PRESCRITES DANS LA NORME SUR

LE MATERIEL BROUILLEUR; “APPAREILS NUMERIQUES”, NMB-

003 EDICTEE PAR LE MINISTRE DES COMMUNICATIONS.

CAUTION:

Changes or modifications not approved by JVC could void

the user’s authority to operate the equipment.

[European Union only]

[Union européenne seulement]

Caution —

(Standby/on) button!

Disconnect the mains plug to shut the power off completely

(the STANDBY lamp goes off). When installing the apparatus,

ensure that the plug is easily accessible. The (Standby/on)

button in any position does not disconnect the mains line.

• When the system is on standby, the STANDBY lamp lights

red.

• When the system is turned on, the STANDBY lamp goes off.

The power can be remote controlled.

ATTENTION—Touche

(attente/sous tension)!

Déconnectez la fiche secteur pour mettre l’appareil

complètement hors tension (le témoin STANDBY l s’éteint).

Lors de l’installation de l’appareil, assurez-vous que la fiche

soit facilement accessible. La touche (attente/sous tension)

dans n’importe quelle position ne déconnecte pas l’appareil

du secteur.

• Quand l’appareil est en mode d’attente, le témoin STANDBY

est allumé en rouge.

• Quand l’appareil est sous tension, le témoin STANDBY

s’éteint.

L’alimentation peut être commandée à distance.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR

MOISTURE.

CAUTION

To reduce the risk of electrical shocks, fire, etc.:

1. Do not remove screws, covers or cabinet.

2. Do not expose this appliance to rain or moisture.

ATTENTION

Afin d’éviter tout risque d’électrocution, d’incendie, etc.:

1. Ne pas enlever les vis ni les panneaux et ne pas ouvrir le

coffret de l’appareil.

2. Ne pas exposer l’appareil à la pluie ni à l’humidité.

For USA-California Only

This product contains a CR Coin Cell Lithium Battery which

contains Perchlorate Material – special handling may

apply.

See www.dtsc.ca.gov/hazardouswaste/perchlorate

CAUTION:

• Do not block the ventilation openings or holes. (If the

ventilation openings or holes are blocked by a newspaper

or cloth, etc., the heat may not be able to get out.)

• Do not place any naked flame sources, such as lighted

candles, on the apparatus.

• When discarding batteries, environmental problems

must be considered and local rules or laws governing the

disposal of these batteries must be followed strictly.

• Do not expose this apparatus to rain, moisture, dripping

or splashing and that no objects filled with liquids, such as

vases, shall be placed on the apparatus.

• Excessive sound pressure from earphones or headphones

can cause hearing loss.

CAUTION: Proper Ventilation

To avoid risk of electric shock and fire, and to prevent

damage, locate the apparatus as follows:

1. Front: No obstructions and open spacing.

2. Sides/Top/Back: No obstructions should be placed in the

areas shown by the dimensions below.

3. Bottom: Place on the level surface. Maintain an adequate

air path for ventilation by placing on a stand with a height

of 10 cm or more.

Front view

Side view

GVT0242-019A EN_UX-GP5[JC]ff

How to cancel the demonstration

Press and hold DEMO button while on standby. (Refer to the attached “Information

about the demonstration function.”)

1 2 3 4

Summary of Contents

Page 1 - MICRO COMPONENT SYSTEM

Page 2 - BT-51018-5

Setting the ClockWithout setting the built-in clock, you cannot use Daily Timer and Sleep Timer.• “0:00” flashes on the main display until you set t

Page 3 - Precautions

CAUTION: Proper VentilationTo avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:1. Front: No obstructions

Page 4

Setting the ClockWithout setting the built-in clock, you cannot use Daily Timer and Sleep Timer.• “0:00” flashes on the main display until you set t

Jvc UX-GP5 User Manual

Browse online or download User Manual for Acoustics Jvc UX-GP5. JVC UX-GP5 User Manual [ru]

Summary of Contents

More documents for Acoustics JVC UX-GP5

Comments to this Manuals

Jvc UX-GP5 User Manual

Browse online or download User Manual for Acoustics Jvc UX-GP5. JVC UX-GP5 User Manual [ru]

Summary of Contents

More documents for Acoustics JVC UX-GP5

Comments to this Manuals

Related products and manuals for Acoustics Jvc UX-GP5