DOME CAMERATK-C210FWTK-C215V4TK-C215V12INSTRUCTIONSFor Customer Use:Enter below the Serial No. which is located on the body. Retain this information f
10Introduction (continued)Set the video setting switches on the camera unit before mounting it.To set the switches, use a fine-tipped screwdriver.A [R
113.[SYNC] Synchronization system selection switch.This switch sets the synchronizing system for the camera.INT:This is set for internal synchronizati
12Introduction (continued)Set the video setting switches on the camera unit before mounting it.To set the switches, use a fine-tipped screwdriver. A [
132.[SELECT] WHT.BAL./PHASE setting switch.WHT.BAL.:The F [R/B, +/-] buttons are used as [R/B] adjustment buttons.PHASE:The F [R/B, +/-] buttons are u
14Installation and connectionSet the video setting switches on the camera unit before mounting it.To set the switches, use a fine-tipped screwdriver.A
15DC 12 V or AC 24 V power supply cableConnect the DC 12 V or the AC 24 V power supply to the DC 12 V/AC 24 V terminals on the terminal board. To prev
16Installation and connection (continued)NOTE: ● Turn OFF the power supply to all equipment to b
17Getting StartedCAUTION: ● When mounting the camera to the ceiling, ensure to wear safety glasses
18Installation and connection (continued)Embedding the camera to the ceiling* Make use of a ceiling material with a thickness between 9.5 mm to 22 mm.
19䡵 Connecting1. Attach the fall prevention wire to the camera, followed by attaching it to the ceiling slab (Fall prevention wire is not included.)2.
2IntroductionInformation for Users on Disposal of Old Equipment[European Union]This symbol indicates that the electrical and electronic equipment shou
20Installation and connection (continued)When mounting the camera directly to the ceiling or on the wallWhen mounting to a wall, replace areas indicat
214.Connect the video signal cable. (Apg. 14)Lower the protection cover and connect the connectors. Upon connecting, restore the protection cover to c
22Installation and connection (continued)When mounting the camera to the electrical boxNOTE: Bef
23Adjusting ImageUpon mounting the camera, adjust the images while checking the actual image.Mounting the test monitorConnect the [MONITOR] terminal o
24Adjusting Image (continued)Adjusting the field angle/focus/brightness(Not available on TK-C210FW)Upon determining the imaging direction, adjust the
25䡵 TK-C215V12● 2 types of angle of view may be selected for TK-C215V12. In general, set in a way such that the home position shoots a wide range and
26Adjusting Image (continued) Registering alarm positionFor registering the angle of view during monitoring when there is an alarm input.1. Check tha
27As a general characteristic unique to CCDs, white-spots may appear on the screen with age.In order to reduce this phenomenon, this unit is equipped
28Others䡵 CameraSignal system:U type : Based on NTSC standardE type : Based on PAL standardScanning frequenciesU type : 15.734 kHz (Horizontal), 59.94
29䡵 GeneralPower supply : AC 24 V H 50 Hz/60 Hz DC 12 V dPower consumptionTK-C210FW:E type : 220 mATK-C215V4:U type : 4.2 WE type : 340 mATK-C215V12:U
3I䢇 The unit is to be powered by a DC 12 V or an AC 24 V power supply.䢇 The unit is to be powered by a UL Listed DC 12 V or an AC 24 V power supply. (
30Others (continued)䡵 External Dimensions[Unit: mm (inches)] When cover is attached When embedded* Specifications and appearance of this unit and r
31Focus chartTK-S215_EN.book Page 31 Tuesday, March 28, 2006 9:39 AM
© 2006 Victor Company of Japan, Limited LST0308-001CTK-C210FW/TK-C215V4/TK-C215V12DOME CAMERATK-S215_EN.book Page 32 Tuesday, March 28, 2006 9:39 A
4Introduction (continued)These are general IMPORTANT SAFEGUARDS and certain items may not apply to all appliances.1. Read all of these instructions.2.
5Thank you for purchasing this product.(These instructions are for: TK-C210FWE, TK-C215V4U/E, TK-C215V12U/E.)Before beginning to operate this unit, pl
6Introduction (continued)IntroductionSafety Precautions ... 2Characteristics ...
7䢇 To save energy, when it is not being used turn the system’s power off.䢇 This camera has been designed for indoor use. It cannot be used outdoors.䢇
8Introduction (continued)CameraAMounting hole (elliptical) x 4Use these when mounting the camera to the electrical box. (A pg. 22)NOTE:
9Camera (Interior)The picture below shows the camera when the dome cover and outer case are removed.Procedures for removal. (A pg. 18 AEmbedding the c
Comments to this Manuals