Jvc TH-S11B User Manual download pdf (Page 11)

Connections

Do not connect the power cord until all other connections have been made.

NOTE

• Place the satellite speakers on a flat and level surface.

• The front and center speakers are magnetically shielded to avoid color

distortions on TVs. However, if not installed properly, they may

cause color distortions. So, pay attention to the following when

installing the speakers.

– When placing the speakers near a TV set, turn off the TV’s main

power switch or unplug it before installing the speakers. Then wait

at least 30 minutes before turning on the TV’s main power switch

again.

Some TVs may still be affected even though you have followed the

above. If this happens, move the speakers away from the TV.

• The surround speakers and the subwoofer are not magnetically

shielded.

If it is located nearby the TV or monitor, it will probably cause

color distortion on the screen. To avoid this, do not place the

speaker nearby the TV or monitor.

• Be sure to place the subwoofer to the TV’s right side. If you place the

subwoofer to the TV’s left side, keep sufficient distance between

them to prevent the TV screen from appearing mottled.

• Distortion of picture may occur when connecting the TV via a

VCR, or to a TV with a built-in VCR.

• You need to set “MONITOR TYPE” in the PICTURE menu

correctly according to the aspect ratio of your TV. (See page 29.)

7 To connect a TV equipped with the component video

input jacks

NOTE

• If your TV supports progressive video input, you can enjoy a high

quality picture by setting the progressive scan mode to active. (See

page 12.)

• If the component video input jacks of your TV are of the BNC type,

use a plug adapter (not supplied) to convert the pin plugs to BNC

plugs.

• The video signals can be output only when you select “DVD” as the

source to play. (See page 11.)

7 To connect a TV equipped with the S-VIDEO and/or

the composite video input jacks

NOTE

• Select the appropriate scan mode according to your TV. (See page

12.)

You can enjoy the sound of an analog component.

NOTE

• If you connect a sound-enhancing device such as a graphic equalizer

between the source components and this system, the sound output

through this system may be distorted.

• When playing a video component such as a VCR;

• To listen to the sound, select “AUX” as the source to play. (See

page 11.)

• To see the picture, connect the video output jack of the component

to the video input jack of the TV directly, and select the correct

input mode on the TV.

Make sure that all other connections have been completed.

CAUTION

• Disconnect the power cord before cleaning or moving the system.

• Do not pull on the power cord to unplug the cord. When unplugging

the cord, always grasp and pull the plug so as not to damage the cord.

NOTE

• Preset settings, such as preset stations and surround mode adjustment,

may be erased in a few days in the following cases;

• If you unplug the power cord of the center unit.

• If a power failure occurs.

Speaker layout

Connecting a TV

Front right

speaker

Center speaker

Subwoofer

Surround left

speaker

Surround right

speaker

Front left

speaker

Center unit

To component

video input

Component video cord (not supplied)

Connecting an external

component

Connecting the power

cord

Center unit

S-VIDEO cord

(not supplied)

Composite video cord

(supplied)

RCA pin plug cord

(not supplied)

Center unit

VCR

Cassette recorder

To audio output

Center unit

Power cord

Plug into AC outlets.

TH-S11B[J].book Page 8 Tuesday, May 8, 2007 4:15 PM

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 39 40

Comments to this Manuals

No comments

Jvc TH-S11B User Manual Page 11

Comments to this Manuals

Related products and manuals for Home Theater Systems Jvc TH-S11B