For Customer Use:Enter below the Model No. and Serial No. which are located either on the rear, bottom or side of the cabinet. Retain this information
7EnglishDigital connectionsThis receiver is equipped with one DIGITAL OUT terminal andthree DIGITAL IN terminals — one digital coaxial terminal and tw
8EnglishTurning the Power On and Off (Standby)On the front panel:To turn on the power, press POWER.The STANDBY lamp goes off. The name of thecurrent s
9EnglishSelecting different sources for picture and soundYou can watch picture from a video component while listening tosound from another component.
10EnglishAdjusting the Subwoofer Output LevelYou can adjust the subwoofer output level if you have selected“YES” for the “SUBWOOFER” (see page 15).Onc
11EnglishChanging the Source NameWhen you have connected the MD recorder to the TAPE/MD jacksor the DBS tuner to the TV SOUND/DBS jacks on the rear pa
12EnglishSetting the Speakers for the DSP ModesTo obtain the best possible surround sound of the DSP (DigitalSignal Processor) modes (see page 18), yo
13EnglishCrossover Frequency SettingSmall speaker cannot reproduce the bass sound very well. So, if youhave used a small speaker any for the front, ce
14EnglishDigital Input (DIGITAL IN) TerminalSettingWhen you use the digital input terminals, you have to register whatcomponents are connected to whic
15EnglishTo cancel the One Touch Operation functionPress ONE TOUCH OPERATION (INPUT ATT.) so that the ONETOUCH OPERATION indicator goes off.(Even thou
16EnglishUsing Preset TuningOnce a station is assigned to a channel number, the station can bequickly tuned. You can preset up to 30 FM and 15 AM stat
RX-6000VBK/RX-6008VBK[J]/RX-6500VBK[J]Errata SheetPlease notice the following modifications when reading Instructions.Page 18.IncorrectNotes:• If “REA
17EnglishSelecting the FM Reception ModeWhen an FM stereo broadcast is hard toreceive or noisyYou can change the FM reception mode while receiving an
18EnglishUsing the DSP ModesThe built-in Surround Processor provides three types of the DSP (Digital Signal Processor) mode — 3D-PHONIC mode,DAP (Digi
19EnglishJVC Theater SurroundIn order to reproduce a more realistic sound field in your listeningroom while playing soundtracks of software encoded wi
20EnglishAvailable DSP Modes According to the Speaker ArrangementAvailable DSP modes will vary depending on how many speakers are used with this recei
21EnglishAdjusting the DAP Modes andHeadphones modeOnce you have adjusted the DAP modes, the adjustment ismemorized for each DAP mode.Before you start
22EnglishFrom the remote control:1. Press SURROUND MODErepeatedly until the DAP mode —LIVE CLUB, DANCE CLUB,HALL, PAVILION, or HEADPHONE — appears on
23English4. Adjust the speaker output levels.• To adjust the center speaker level, pressCNTR –/+ (from –10 dB to +10 dB).• To adjust the left rear spe
24EnglishOn the front panel:You can also use the buttons on the front panel to adjust theSurround modes. However, no test tone is available when using
25EnglishActivating the DSP ModesYou can use only one DSP mode at a time. When a DSP mode isactivated, another DSP mode is canceled if in use.For Dolb
26EnglishCOMPU LINK Remote Control SystemThe COMPU LINK remote control system allows you to operate JVC audio components through the remote sensor ont
G-1Warnings, Cautions and OthersFloorSpacing 15 cm or moreStand height 15 cm or moreWall or obstructionsFrontCaution: Proper VentilationTo avoide risk
27EnglishAV COMPU LINK Remote Control SystemThe AV COMPU LINK remote control system allows you to operate JVC video components (TV, VCR, and DVD playe
28EnglishOne-Touch DVD PlaySimply by starting playback on the DVD player, you can enjoy theDVD playback without setting other switches manually.• When
29EnglishSound control section (Amplifier)You can always perform the following operations:SURROUND: Turns on or off the Surround modes —Dolby Pro Logi
30EnglishIMPORTANT:To operate JVC’s video components using this remote control:• You need to connect JVC video components through the AVCOMPU LINK ter
31EnglishManufacturer Code Manufacturer Code Hitachi 10 Samsung 12 JVC 01 Sanyo 13 Magnavox 02 Sony 07 Mitsumishi 03 Sharp 06 Panasonic 04, 11 To
32EnglishManufacturer Codes Manufacturer CodesEmerson 11 Philips 09Fisher 29 RCA 05, 06Funai 10, 14, 15, 16 Samsung 24GoldStar 12 Sanyo 21, 22, 23Hita
33EnglishTroubleshootingUse this chart to help you solve daily operational problems. If there is any problem you cannot solve, contact your JVCservice
34EnglishSpecificationsAmplifierOutput PowerAt Stereo operation:Front channels:100 W per channel, min. RMS, driven into 8 Ω40 Hz to 20 kHz with no mor
35EnglishFM tuner (IHF)Tuning Range: 87.5 MHz to 108.0 MHzUsable Sensitivity: Monaural: 12.8 dBf (1.2 µV/75 Ω)50 dB Quieting Sensitivity: Monaural: 21
Sophisticated electronic products may require occasional service. Just as quality is a keyword in the engineering and production ofthe wide array of J
1EnglishTable of ContentsUsing the DSP Modes ... 18Available DSP Modes According to the Speaker Arrangement .. 20Adjustin
LIMITED WARRANTY AUDIO-2JVC COMPANY OF AMERICA warrants this product and all parts thereof, except as set forth below ONLY TO THE ORIGINALPURCHASER AT
VICTOR COMPANY OF JAPAN, LIMITEDENJVC1299HIMMDWJEINRX-6500V[J]COVER/1 99.12.10, 6:15 PM2
2EnglishParts IdentificationBecome familiar with the buttons and controls on the receiver before use.Refer to the pages in parentheses for details.Fro
3EnglishANTENNAAMLOOPAMEXTAMEXTAMLOOPFM 75 COAXIALAMLOOPANTENNAAMEXTFM 75 COAXIALFM 75 COAXIALANTENNAGetting StartedThis section explains how to
4English++–2121–FRONT SPEAKERSLEFTRIGHTBasic connecting procedure1 Cut, twist and remove the insulation at the end ofeach speaker signal cable (not su
5EnglishConnecting the subwoofer speakerYou can enhance the bass by connecting a subwoofer.Connect the input jack of a powered subwoofer to theSUBWOOF
6EnglishRIGHTRIGHT LEFTAUDIOVCRIN(PLAY)OUT(REC)CDPHONOTV SOUND/DBSTAPE/MDIN(PLAY)OUT(REC)VIDEOVIDEOS-VIDEOMONITOROUTVCRIN(PLAY)OUT(REC)DBSDVDRIGHTLEFT
Comments to this Manuals