JVC DT-V20L3GZ User Manual download pdf (Page 15)

SCOPE SETTING*

Settings for the wave form monitor and vector scope

Item To do Setting value

GAIN

Adjust the gain level for the incoming wave form data. –10 – +10

SIZE*

Select the size of the wave form monitor and vector scope window. NORMAL, LARGE

POSITION*

Select the position of the wave form monitor and vector scope

window.

1 (lower right), 2

(lower left), 3 (upper

left), 4 (upper right)

TRANSPARENT

Activates/deactivates the function to make the window translucent.

ON (translucent),

OFF (normal)

AUTO OFF

Activates/deactivates the function to make the wave form monitor and

vector scope window go off automatically 15 minutes after displaying it.

ON, OFF

WAVE DISPLAY

Select the wave form for the wave form monitor. Y/Pb/Pr (HD signals)

Y/Cb/Cr (SD signals)

R/G/B (RGB signals)

WAVE FILTER

Activates/deactivates the low-pass filter for the incoming wave form

data.

FLAT (no filter),

LOWPASS

WAVE OVER

LEVEL

Adjust the over level for the incoming luminance (Y) and RGB

signals.

☞ “NOTE”

MARKING

Activates/deactivates the function to change the color of a wave form

when the signal exceeds the limit specified on “LEVEL” (☞ below).

OFF, ON

LEVEL

Adjust the lower limit for the over level. 070 – 109

Wave form monitor does not work for DVI signals (PC input). Vector scope does not work for RGB signals.

When you set “SIZE” to “LARGE,” the window is displayed in the center of the screen regardress of the “POSITION”

setting.

SYNC FUNCTION

Settings for the synchronization with signals

Item To do Setting value

NO SYNC ACTION

Select the screen status when no signal is coming in. OFF, P.SAVE (power save

mode), GRAY B. (gray screen)

DELAY TIME

Select the period until the screen status changes as selected

in “NO SYNC ACTION” after signals stop coming in.

30sec., 5min., 15min.

SYNC INPUT

SEL.*

Select the sync signal for the VIDEO1, VIDEO2 and

COMPO./RGB input.

INT. (Internal sync),

EXT. (External sync)

LOW LATENCY

Activates/deactivates the function to shorten the time

taken to display the picture (low latency function).

• If the picture is not displayed steadily while “ON” is

selected, select “OFF.”

• While “ON” is selected, the displayed picture may

become unstable when an operation using buttons on

the front panel or the menu is performed, or when the

signal format changes.

ON, OFF

• When setting “NO SYNC ACTION” to “GRAY B.,” the screen color changes to gray and the power consumption

of the back light is saved by half. Selecting “P.SAVE” (power save mode) saves more power consumption by

turning off the back light.

• In the initial setting, “NO SYNC ACTION” is set to “P.SAVE”, and “DELAY TIME” set to “15min.” Change the

settings if necessary.

Memorized for each input.

Operation guide

Shows the buttons for each

operation.

Example of the vector scope

Ex.: When the color bar is displayed

NOTE

• The menu automatically disappears in about 30 seconds after the previous operation.

• Some items may not appear on the menu depending on the input or the input signal.

• The items controlled by the MAKE system do not appear on the menu.

Example of the wave form monitor

Ex.: When the luminance signal is Y, “MARKING” is set to “ON”

and “LEVEL” is set to “080”

• The wave which goes over the value set on “LEVEL” is

indicated in red.

• The display differs depending on the input signal or the

setting of “WAVE DISPLAY.”

Video signal

EndStart

Red White

DT-V24G1_20L3G_US.indd 15DT-V24G1_20L3G_US.indd 15 11.1.20 4:49:54 PM11.1.20 4:49:54 PM

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 27 28

Comments to this Manuals

No comments

JVC DT-V20L3GZ User Manual Page 15

Comments to this Manuals

Related products and manuals for Supplementary music equipment JVC DT-V20L3GZ