JVC TK-C1480 User Manual download pdf (Page 7)

E-12

REC

PLAY

FFREW

REVERSE

PAUSE/

STILL

REC

CHECK

STOP/EJECT

COUNT/

CLOCK

TIME

MODE

TIMER

REC

AL/PL

RESET

VIDEO CASSETTE RECORDER

SHIFT/TRACKING

SET/V.LOCK

RESET

/CANCEL

OPERATE

SR-L910

OPE. LOCK

TO CAMERATO CAMERA DATA I / ODATA I / O

RXRX

TXTX

COMCOM

1 2 3 4 5 6 7 8

COMCOM

9/19/1 10/210/211/311/3 12/412/4 13/513/514/614/6 15/715/7 16/816/8

COMCOM COMCOM COMCOM

CAMERACAMERA

SWSW

UNITUNIT

ALARMALARM

AUTOAUTO

431 2 875 6

2 3 4 5 6 7

MONITORMONITOR

OUTPUTOUTPUT

MONITORMONITOR

SERIAL-2SERIAL-2SERIAL-1SERIAL-1

VIDEO INPUTVIDEO INPUT

VIDEO OUTPUTVIDEO OUTPUT

OUTPUTOUTPUT

ONON

2 3 4 5 6 7

POWER

OFF

AC INPUT

ALC

LEVEL

Av Pk

L H

ALC

LEVEL

Av Pk

L H

ALC

LEVEL

Av Pk

L H

•••••

CAMERA

Remote Control Unit

RM-P2580

Time lapse VCR

MONITOR

CAM SW

OUT

VIDEO IN

COM

CAMERA

MONITOR

OUTPUT 2

MONITOR

OUTPUT 1

CONNECTION/INSTALLATION

RM-P2580 System

 System with up to 8 cameras

Camera

TK-C1480

Camera

TK-C1480

Camera

TK-C1480

Camera 1

Camera 2

Camera 8

Control signal cable

Video signal cable

Power

cable

AC24V

DC12V

AC24V

DC12V

AC24V

DC12V

MONITOR screen

(example showing camera ID as

“05”)

This is the connected example of the TK-C1480U or TK-C1480E.

When controlling with any system except the RM-P2580, execute proper settings using

switches and menu screens according to the systems used. ( Page 14)

PROT OOLDUPLEXID-05C

“DUPLEX” should

be displayed.

The number shown in the

□□ part of ID-□□

should be correct.

MACHINE ID:1

(Menu screen)

RX TERM: OFF

(switch)

MACHINE ID:2

(Menu screen)

RX TERM: OFF

(switch)

MACHINE ID:8

(Menu screen)

RX TERM: ON

(switch)

MEMO

• When operating a system using the RM-P2580, several cameras (up to 8) can be

connected and used on one control signal cable. Consequently, an incorrect switch setting

on just a single camera will cause the entire system to work incorrectly.

• Confirm switch settings on the screen as follows.

q Confirm that the image from the camera to be checked

is displayed on the monitor.

w Turn OFF and then ON the AC 24 V power to the

camera to be checked.

e The camera begins the initial operation and charac-

ters similar to those shown in the illustration on the

right appear on the monitor screen.

r Confirm that “DUPLEX” and

“ID-□□” are displayed

and that the ID number is the correct number (the

number should be the same as the number of the

VIDEO INPUT terminal to which the camera is con-

nected on the rear panel of the RM-P2580).

t If wrong, set the camera ID again.

E-13

CAMERA

SETUP

SET

EXT TERM-OFF

INT/GL

DUPLEX

RX TERM-OFF

NOT USED

SIMPLEX

EXT TERM-OFF

INT/GL

DUPLEX

RX TERM-OFF

NOT USED

SIMPLEX

VIDEO

IRIS

AWC

A RX

B RX

C TX

D TX

RM-P2580

Camera 2

control signal

connection terminals

Connect:

Camera TX+ to RM-P2580 RX+

Camera TX– to RM-P2580 RX

–

Camera RX+ to RM-P2580 TX+

Camera RX– to RM-P2580 TX–

The A B C D marks indicated on both the

camera terminals and the RM-P2580 termi-

nals facilitate correct connections. Connect

the terminals with identical marks.

 Connecting the control signal cable

(Use a twisted-pair cable for connection.  Page 17.)

Camera 1

control signal

connection terminals

 Setting the switches ( Page 10)

Select the synchronization method of the

camera image.

Set the switch on all cameras to LL (Line Lock)

and match with the V. PHASE.

( Page 26.)

Set this switch to the DUPLEX

* If the setting is changed, be absolutely sure to

switch on the power again.

Set this switch to ON (signal termination ON)

only on the camera placed at the end of the

control signal cable.

Set to OFF on all other cameras.

 Setting on the MENU screen ( Page 33)

* If the setting is changed, escape from the menu screen once, and definitely switch on the power again.

MACHINE ID setting switches

Set this item to match the RM-P2580 VIDEO

INPUT terminal number for each camera.

When connecting

● Turn OFF the power supply to all equipment to be used before making connections.

● Carefully read the Instructions for each piece of equipment to be used before making

connections.

● For the appropriate connection cables and the length of these, carefully read “Connections

on the back” on page 16.

● The control signal cable cannot be used for loop connection.

Set to M.DROP

Set to M.DROP when the RM-P2580 is used

as a remote control unit. When controlling

from another machine, make sure that it

matches the communication system used.

MMCO UNICAT ION

ST LE M.DROPY

MA H N E DII 1C

1 2 3 4 5 6 7 8 9 10 11 12 ... 19 20

Comments to this Manuals

No comments

JVC TK-C1480 User Manual Page 7

Comments to this Manuals

Related products and manuals for Security cameras JVC TK-C1480