JVC LVT2121-001A User Manual download pdf

0310YOMMDWCDT

DOWN

SET

LVT2121-001A[J/C]

Front view / Face

Side view / Côté

DEMO

DEMO OFF

DIM 1

DIM 2

DIM OFF

TURBO ON

TURBOOFF

HBS ON

HBS OFF

ROCK POP

CLASSIC

JAZZ

FLAT

SLEEP 10

SLEEP 20 SLEEP 30

SLEEPOFF

• • •

SLEEP180

SET

DAILY 1 DAILY 2 DAILY 3

SET

DOWN

ASTB ON

ASTB OFF

For customer use:

Enter below the Model No. and Serial No. which

are located either on the rear, bottom or side of the

cabinet. Retain this information for future reference.

Model No.

Serial No.

Microsoft and Windows Media are either registered

trademarks or trademarks of Microsoft Corporation in

the United States and/or other countries.

iPod is a trademark of Apple Inc., registered in the U.S.

and other countries.

“Made for iPod” means that an electronic accessory

has been designed to connect specifically to iPod and

has been certified by the developer to meet Apple

performance standards.

Apple is not responsible for the operation of this

device or its compliance with safety and regulatory

standards.

•

For USA-California Only

This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material—special handling may apply.

See www.dtsc.ca.gov/hazardouswaste/perchlorate

Prepare the remote control

When you use the remote control for the first time, pull out the insulation sheet.

To replace the battery in the remote control

❍

Display settings

Display/illumination brightness

You can dim the display window and illumination.

Display information

You can change the information shown on the

display.

Ex.: During playback of a CD...

The information shown on the display differs

depending on the source.

Tag information is shown on the display while an

MP3/WMA file is played back.

❍

•

Sound adjustments

Fade muting

To drop the volume in a moment

To restore the volume, press again or adjust the

volume level.

Sound Turbo

To emphasize the sound

Hyper Bass Sound (HBS)

To reinforce the bass sound

Sound Mode

To select the sound mode suitable for your favorite

music

❍

•

Setting the clock

If you have already set the clock before, press and

hold CLOCK/TIMER until the current time is shown

on the display then press SET to activate the clock

setting mode.

2 Adjust the hour and minute.

To go back to the previous step, press MENU/

CANCEL.

The clock may gain or lose 1 to 2 minutes per month.

You may need to readjust the clock periodically.

•

MICRO COMPONENT SYSTEM

UX-F3B

—consists of CA-UXF3B and SP-UXF3BJ

Notes on the power cord

When you go away for an extended period of time,

remove the plug from the wall outlet.

When unplugging the System from the wall outlet,

always pull the plug, not the power cord.

Do not handle the power cord with wet hands.

Disconnect the power cord before cleaning the System or

moving the System.

Do not alter, twist or pull the power cord, or put anything

heavy on it, which may cause fire, electric shock, or other

accidents.

Avoid moisture, water, dust, and high temperatures

Do not place the System in moist or dusty places.

If water gets inside the System, turn off the power and

remove the plug from the wall outlet, then consult your

dealer. Using the System in this state may cause a fire or

electrical shock.

Do not expose the System to direct sunlight or place it

near a heating device.

•

Lithium coin battery

(product number:

CR2025)

For better FM reception

Disconnect the supplied FM antenna, and connect to an outdoor FM antenna

(not supplied) using a 75 Ω wire with coaxial type connector.

To a wall outlet

FM antenna (supplied): Extend it so that you can obtain the best reception.

Maintenance

To get the best performance of the System, keep your discs

and the mechanism clean.

Handling discs

Remove the disc from its case by holding it at the edge

while pressing the center hole lightly.

Do not touch the shiny surface of the disc, or bend the

disc.

Put the disc back in its case after use.

Be careful not to scratch the surface of the disc when

placing it back in its case.

Avoid exposure to direct sunlight, temperature extremes,

and moisture.

To clean the disc:

Wipe the disc with a soft cloth in a straight line from

center to edge.

Cleaning the System

Stains should be wiped off with a soft cloth. If the System

is heavily stained, wipe it with a cloth soaked in water-

diluted neutral detergent and wrung well, then wipe

clean with a dry cloth.

Since the System may deteriorate in quality, become

damaged or get its paint peeled off, be careful about the

following:

DO NOT wipe it hard.

DO NOT wipe it with thinner or benzine.

DO NOT apply any volatile substances such as

insecticides to it.

DO NOT allow any rubber or plastic to remain in contact

for a long time.

•

–

NOTES:

Make sure the antenna conductors do not touch any other terminals, connecting cords or the power cord. Also, keep the antennas away

from metallic parts of the System, connecting cords, and the AC power cord. Otherwise, it could cause poor reception.

When connecting the speaker cords, match the polarities of the speaker terminals: red to (+) and black to (–).

DO NOT connect more than one speaker to each terminal.

Use only speakers with the same speaker impedance as indicated by the speaker terminals on the rear of the System.

DO NOT allow the conductor of the speaker cords to come into contact with the metallic parts of the System.

•

Notes on installation

Select a place which is level, dry and neither too hot nor

too cold—between 5˚C and 35˚C (41°F and 95°F).

Do not install the System in a place subject to vibrations.

Do not put heavy objects on the System.

To prevent malfunction or damage to the System

Do not insert any metallic objects, such as wires, hairpins,

coins, etc. into the System.

Do not block the vents.

There are no user-serviceable parts inside. If anything

goes wrong, unplug the power cord and consult your

dealer.

•

Precautions

For turning off the demonstration display, see

“Canceling the display demonstration” in “Initial

settings.”

Playable disc/file

This System can play back...

Audio CD and CD-R/CD-RW in Audio CD format.

MP3/WMA files on a CD-R/CD-RW (ISO 9660 format).

This System cannot play “packet write” discs.

This System can recognize up to 255 groups on a disc.

The total number of groups and tracks (on a disc) that can

be recognized by the System is 512 (for MP3/WMA).

For MP3/WMA playback...

Some MP3/WMA files may not be played back due to

their recording conditions.

This System can play only discs of ISO 9660 Level 1 or

Level 2.

It is recommended to record each file at a sampling rate

of 44.1 kHz and at a data transfer rate of 128 kbps.

This System cannot play back files made at a bit rate of

less than 64 kbps.

This System can show the Tag data (Version 1).

•

–

•

–

Supplied accessories

After unpacking, check to make sure that you have all

the following items:

Remote control (× 1)

Lithium coin battery CR2025 (× 1)

The battery has been installed in the remote

control when shipped from the factory.

FM antenna (× 1)

If anything is missing, consult your dealer immediately.

❍

•

–

•

NOTES:

Store the battery in a place where children cannot reach. If a child accidentally swallows the battery, consult a doctor immediately.

To prevent the battery from overheating, cracking, or starting a fire:

Do not recharge, short, disassemble or heat the battery or dispose of it in a fire.

Do not leave the battery with other metallic materials.

Wrap the battery with tape and insulate when throwing away or saving it.

Do not poke the battery with tweezers or similar tools.

Dispose of battery in the proper manner, according to federal, state, and local regulations.

The battery (battery pack or battery installed) shall not be exposed to excessive heat source such as sunshine, fire or the like.

•

–

•

Getting started

CAUTION:

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

Specifications

Main unit (CA-UXF3B)

General

Power source: AC 120 V

, 60 Hz

Power consumption (at operation): 40 W

Power consumption (on standby): 1.00 W or less

Dimensions (approx.) (W x H x D) (including projecting

parts): 236 mm × 123 mm × 285 mm

(9-5/16” × 4-7/8” × 11-1/4”)

Mass (approx.): 2.0 kg (4.5 lbs)

Amplifier

Output Power: 60 W (30 W + 30 W) at 6 Ω (10% THD)

Audio Input: AUDIO IN: Stereo mini (ø 3.5 mm)

Speaker impedance: 6 Ω - 16 Ω

Tuner

FM frequency: 87.5 MHz – 108.0 MHz

iPod

Output power: DC 5 V 500 mA

Video out: Composite

Speaker (SP-UXF3BJ)

Speaker type: Bass-reflex type

Tweeter: 4 cm (1-5/8”)

Woofer: 12 cm (4-3/4”)

Impedance: 6 Ω

Dimensions (approx.) (W x H x D) (including projecting

parts): 141 mm × 250 mm × 181 mm

(5-9/16” × 9-7/8” × 7-3/16”)

Mass (approx.): 1.7 kg (3.8 lbs) each

Supplied accessories

See “Supplied accessories” in “Getting started.”

Design and specifications are subject to change without

notice.

Red

Black

From left speaker

From right speaker

Red

Black

If the System does not work correctly, disconnect the AC power cord from the wall outlet, wait for a while, and

connect the cord again.

•

Troubleshooting

If you are having a problem with your System, check this list for a possible solution before calling for service.

To cancel a Daily Timer

1 Select a Daily Timer number.

2 Cancel the selected Daily Timer.

The timer indicator is turned off.

Auto Standby

You can turn off the System automatically.

The A.STBY indicator starts flashing after playback

stops. If no operation is done for about 3 minutes, the

System is turned off.

This function cannot be used when “TUNER FM” or

“AUDIO IN” is selected as the source.

•

Sleep Timer

Specify the time (in minutes.)

To check the remaining time until the System shuts off,

press SLEEP once.

Daily Timer

By using Daily Timer, you can wake up with your favorite

music.

You can store three Daily Timer settings.

Tune into a station, insert a disc or connect iPod to the

System beforehand.

1 Select a Daily Timer number.

2 Set the timer contents.

Hour and minute for the on-time and off-time

Playback source

Volume

If you select “VOL – –,” the volume is set to the

same level as when the System was last turned off.

To correct a misentry during the process, press

MENU/CANCEL. You can return to the previous step.

To exit from Daily Timer setting, press

CLOCK/TIMER repeatedly as required.

3 Turn off the System.

The display disappears and the STANDBY lamp starts

flashing.

While on standby mode, the timer indicator ( ) is

not displayed.

•

–

•

Sound and other adjustments

Timers❍

General

Power does not come on. \ Power plug is not inserted securely. Plug it in securely.

Adjustments or settings are

suddenly canceled before you finish.

\ There is a time limit. Start the procedure again.

Unable to operate the System from

the remote control.

\ The path between the remote control and the remote sensor on the System is

blocked.

\ The battery is exhausted.

No sound is heard. \ Speaker connections are incorrect or loose.

\ Headphones are connected.

FM radio

Hard to listen to broadcasts because

of noise.

\ Antenna connection is incorrect or loose.

\ The FM antenna is not properly extended and positioned.

\ Electrostatic discharge from your body may cause noise. If this happens, turn

the System off then on again.

iPod

The iPod does not play, but

“CONNECT” appears on the display.

\ The iPod battery is low or exhausted. Charge the iPod battery.

Disc

The disc does not play. \ The disc is placed upside down. Place the disc with the label side facing up.

\ The disc is recorded using “packet writing (UDF file system).” It cannot be

played.

“NO DATA” appears on the display. \ MP3/WMA files are not recorded on the disc.

ID3 Tag on an MP3 file cannot be

shown.

\ There are two types of ID3 Tag—Version 1 and Version 2. This System can only

show ID3 Tag Version 1.

Groups and tracks are not played

back as you expect.

\ Playing order is determined when the groups and tracks are recorded. It

depends on the writing application.

The disc sound is discontinuous. \ The disc is scratched or dirty.

The disc tray does not open or close. \ The AC power cord is not plugged in.

\ Disc ejection is prohibited. “LOCKED” appears (see “Prohibiting disc ejection”

in “Disc” on page 2).

Timer

Daily Timer does not work. \ The System was turned on when the on-time came. The timer starts working

only when the System is turned off.

Canceling the display demonstration

When you plug in and turn on the System, the display

demonstration starts automatically if no operation is

done for about 2 minutes.

To cancel the display demonstration

(On the main unit)

(Hold)

Initial settings

In this manual...

The remote control buttons are used for explaining

the operations unless mentioned otherwise. However,

if the System has the same or similar button names,

they can also be used for the operations.

“File” and “track” are used interchangeably.

•

Main unit

Speaker Speaker

Main unit

Connections Do not connect the AC power cord until all other connections have been made.

Normal display

Current track’s elapsed time

Clock

INSTRUCTIONS

(Canceled)

CAUTION: Proper Ventilation

To avoid risk of electric shock and fire, and to prevent

damage, locate the apparatus as follows:

Front: No obstructions and open spacing.

Sides/Top/Back: No obstructions should be placed

in the areas indicated by the dimensions in the

illustration.

Bottom: Place on the level surface. Maintain an

adequate air path for ventilation by placing on a

stand with a height of 10 cm or more.

Monitor

To view video/picture from the iPod

Composite video

cord (not supplied)

To composite video input

Compatible iPod models

iPod model Audio Video

iPod nano

–

iPod nano (2nd Generation)

–

iPod nano (3rd Generation)

iPod nano (4th Generation)

iPod nano (5th Generation)

iPod mini –

iPod mini (2nd Generation)

–

iPod (4th Generation)

–

iPod classic

iPod photo (4th Generation) *

iPod video (5th Generation)

iPod touch

iPod touch (2nd Generation and Fall ‘09)

Only for still picture

If iPod does not play correctly, update iPod software to the

latest version.

For details about updating iPod, check on the Apple web

site <http://www.apple.com/>.

•

(Hold)

ENGLISH

Thank you for purchasing a JVC product.

ATTENTION: Ventilation Correcte

Pour éviter tout risque de choc électrique et d’incendie,

placez l’appareil en respectant ce qui suit:

Avant: Rien ne doit gêner le dégagement.

Flancs/Dessus/Arrière: Aucun obstacle ne doit être

placé dans les zones indiquées par les dimensions

dans l’illustration.

Dessous: Poser l’appareil sur une surface plate.

Laissez suffisamment d’espace pour que la ventilation

puisse s’effectuer correctement en plaçant l’appareil

sur un socle d’une hauteur de 10 cm ou plus.

Enceinte

Appareil principal

UXF3B[JC]5th_F.indd 1UXF3B[JC]5th_F.indd 1 10.4.15 11:27:45 AM10.4.15 11:27:45 AM

1 2

Summary of Contents

Page 1 - Sound and other adjustments

Page 2 - Select a source

TUNER FM AUDIO IN112233112233SETLOCKED UNLOCKEDLEVEL 1SETLEVEL 2LEVEL 3RESUMEiPodiPodUPDOWNSETTUNER FMAUDIO INUPDOWNSETUPDOWN222Resume PlayThis System

Comments to this Manuals

No comments

JVC LVT2121-001A User Manual

Browse online or download User Manual for MP3/MP4 player accessories JVC LVT2121-001A. JVC LVT2121-001A User's Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for MP3/MP4 player accessories JVC LVT2121-001A