JVC HR-S9800U User Manual download pdf (Page 69)

Make connections

Connect an audio/video cable between the VCR’s

audio/video input connectors and the other

component’s audio/video output connectors.

Prepare tapes

Load the source tape on the other VCR, and the

tape to be edited on this VCR.

Select input mode

Select “F-1” — when connecting the other

component to the audio/video input

connectors on the front panel.

Select “L-1” — when connecting the other

component to the audio/video input

connectors on the rear panel.

On the front panel:

Press CH5∞.

On the Remote:

Press the Number key “0 (AUX)” or CH +/–.

Select video input terminal

Follow the procedure described on pages 56 and

60.

When using S VIDEO terminal, set “FRONT AUX

INPUT” (or “REAR AUX INPUT” if you use the

connectors on the rear) to “S-VIDEO”.

When using VIDEO terminal, set “FRONT AUX

INPUT” (or “REAR AUX INPUT”) to “VIDEO”.

Select edit mode

Set the edit mode to “ON” for the VCRs if such a

mode is equipped.

● On this VCR, set “PICTURE CONTROL” to

“EDIT” by following the procedure described

on pages 56 and 57.

Locate end point

1 Press PLAY ( 3 ) to start playback.

2 Press PAUSE ( 8 ) when you find the end of

the scene for which you want to edit.

3 Press C. RESET so that the counter reading

becomes “0:00:00”.

NOTE:

You can also use

( ), the

TIME SCAN SHUTTLE

ring on the front panel, and the

JOG/SHUTTLE

ring on

the Remote to locate the end point (See “Special Effect

Playback”:

墌

pg. 34) .

Locate start point

Use REW ( ), the TIME SCAN SHUTTLE ring

on the front panel, or JOG/SHUTTLE ring on the

Remote to reverse the tape. (See “Special Effect

Playback”: 墌 pg. 34.)

When you find the beginning of the scene you

want to edit, press PAUSE ( 8 ).

Activate editing mode

For Inset Editing:

Press INSERT on the front panel.

For AV Dubbing:

Press INSERT, then press A. DUB on the front

panel.

● Make sure that the recording format (VHS, S-

VHS or S-VHS ET) on the VCR is the same as

that of the original recording on the tape.

● During Insert Editing pause mode (

, and

light up on the front display panel.)

● During AV Dubbing pause mode (

and

blink, and lights up on the front display

panel.)

Start editing

Press PLAY ( 3 ) on this VCR, and start playback

on the other component at the same time.

● During Insert Editing mode ( and light up

on the front display panel.)

● During AV Dubbing mode ( and blink on

the front display panel.)

● When the counter reading becomes “0:00:00”,

editing automatically stops, and the VCR starts

normal playback.

To stop editing any time during recording

Press STOP ( 7 ) on the Remote or STOP/EJECT ( 7 / 0 )

on the front panel.

NOTES:

●

Be sure to select “AUTO” for “PICTURE CONTROL” (or

“NORM” when “VIDEO CALIBRATION” is set to “OFF”) after

you finish editing the tapes (

墌

pg. 56 and 57).

●

Editing cannot be performed on a tape with its record safety

tab removed.

●

The recording speed (SP/EP) is determined by the previous

recording to be replaced. If the recording speed changes on

the tape to be edited while editing the tape, the inserted

picture will be distorted where the recording speed changes.

●

When you edit a tape, a small portion of the recording

preceding to the editing start point will be erased from the

edited tape.

HR-S9800U-EN64-73 00.3.29, 7:30 PM69

1 2 ... 64 65 66 67 68 69 70 71 72 73 74 ... 87 88

Comments to this Manuals

No comments

JVC HR-S9800U User Manual Page 69

Comments to this Manuals

Related products and manuals for Cassette players JVC HR-S9800U