JVC HR-S8009UM User Manual download pdf (Page 12)

Page 12 April 4, 2002 3:07 pm

— 12 —

Function settings

You can use the other useful function settings on the Function Set

screen.

Access Main Menu screen, then

Function Set screen

Press MENU on the Remote. Press rt to

move the highlight bar (arrow) to

“FUNCTION SET”, then press OK or

Select Function

Press rt to move the highlight bar (arrow) to the function you

want to set.

Change setting

Press OK or e. The default setting is bold in the following table.

Press MENU to return to normal screen.

䡵 S-VHS ET — ON/OFF

When this function is set to “ON”, you can record on VHS

cassettes with S-VHS picture quality. Tapes recorded using this

function can be played back on most of S-VHS VCR or VHS VCR

equipped with the SQPB (S-VHS QUASI PLAYBACK) function.

When this function is set to “ON”, the S-VHS indicator lights up

on the display panel.

● Before recording, set “B.E.S.T.” to “ON”. (

墌

See below)

● You cannot activate the S-VHS ET function while recording,

timer-recording or Instant Timer Recording (

墌

pg. 9) or the

“B.E.S.T.” function (

墌

See below) is in progress.

● The S-VHS ET function does not work with S-VHS cassettes.

● To keep the highest quality recording and playback pictures

over a long period of time, S-VHS recording on S-VHS cassettes

is recommended.

● Use of high grade tapes is recommended for S-VHS ET

recordings. On some tapes, picture quality will not improve

even if the S-VHS ET function is used. Check the recording

quality before you start important recordings.

䡵 B.E.S.T. — ON/OFF

When B.E.S.T. (Biconditional Equalized Signal Tracking) system is

set to “ON”, this VCR checks the condition of the tape in use

during playback and recording, and compensates to provide the

highest-possible pictures. This takes place whenever you play

back a tape or start recording after inserting a tape.

NOTE:

The VCR checks the tape condition for about 7 seconds, then

starts recording. To make sure you record the desired scene or

program completely, perform the following steps:

A Press and hold PAUSE (9), and press REC (7). After about

7 seconds, the VCR re-enters Record Pause mode.

B Press PLAY (

) to start recording.

䡵 PICTURE CONTROL — AUTO(NORM)/EDIT/SOFT/SHARP

This function helps you to adjust the playback picture quality

according to your preference.

AUTO (NORM): Normally select this. Picture quality is adjusted

automatically. When “B.E.S.T.” is “OFF”, “NORM” will appear

instead of “AUTO”.

EDIT: Minimizes picture degradation during editing (recording and

playback).

SOFT: Reduces image coarseness when viewing overplayed tapes

containing much noise.

SHARP: Clearer, sharper-edged picture when viewing images with

much flat, same-colored surfaces such as cartoons.

NOTE:

Select “EDIT” when you are editing tapes. After you finish editing

the tapes, select “AUTO”.

䡵 AUTO TIMER — ON/OFF

● When this function is set to “ON”:

The timer recording standby mode is automatically engaged when

the VCR is turned off. It is temporarily canceled when the VCR is

turned on. You do not have to press # to engage or disengage the

timer recording standby mode.

● When this function is set to “OFF”:

You have to press # to engage or disengage the timer recording

standby mode.

䡵 SUPERIMPOSE — ON/OFF

When this function is set to “ON”, various VCR status information

(on-screen display) appears on the screen.

NOTE:

When you use this VCR as the playback VCR for editing a tape, be

sure to set this function to “OFF”; otherwise, the VCR status

information (on-screen display) will be recorded on the edited

tape.

䡵 AUTO SP]EP TIMER — ON/OFF

When this function is set to “ON”, the VCR automatically

switches to EP mode to allow complete recording if there is not

enough tape to record the entire program while timer-recording in

SP mode.

For Example, Recording a program of 140 minutes in length onto

a 120-minute tape

NOTES:

● If you have programed the VCR to timer-record 2 or more

programs, do not use this function, but change the tape speed

manually during timer programing.

● There may be some noise and sound disturbance where the tape

speed switches from SP to EP mode on the tape.

● This function is not available during ITR (Instant Timer

Recording), and will not work properly on the following tapes:

T(ST)-30, T(ST)-60, T(ST)-90, and T(ST)-120.

䡵 VIDEO STABILIZER — ON/OFF

When this function is set to “ON”, you can automatically correct

vertical vibrations in the picture when playing back unstable

recordings made on another VCR.

NOTE:

To watch recordings with close-caption or when you finish

viewing a tape, set this function to “OFF”.

MAIN MENU

FUNCTION SET

TUNER SET

INITIAL SET

PRESS ( , ), THEN (OK)

PRESS (MENU) TO END

VIDEO STABILIZER OFF

BLUE BACK ON

2ND AUDIO RECORD OFF

AUDIO MONITOR HI-FI

S-VHS MODE ON

SELECT WITH ( , ) AND (OK)

PRESS (MENU) TO END

SELECT WITH ( , ) AND (OK)

PRESS (MENU) TO END

FUNCTION

S-VHS ET

OFF

B.E.S.T. ON

PICTURE CONTROL AUTO

AUTO TIMER OFF

SUPERIMPOSE ON

AUTO SP

EP TIMER OFF

Approximately 110 minutes Approximately 30 minutes

SP mode EP mode

– Other Functions –

+5-80(1IP3DJH7KXUVGD\$SULO30

1 2 ... 7 8 9 10 11 12 13 14 15 16

Comments to this Manuals

No comments

JVC HR-S8009UM User Manual Page 12

Comments to this Manuals

Related products and manuals for Cassette players JVC HR-S8009UM